Worked example · Design Technology · Year 9
LNF: Numeracy → Learning about geometry helps us understand shape, space and position, and learning about measurement helps us quantify in the real world → Measurement
A secure Year 9 response, annotated so you can see which success criterion each part meets. It is also the answer key. Key figures: 3 bases rejected (parts 3, 5 and 9), which is 30%; slots C and E rejected; mean base length 120.2 mm (120.23 before rounding); range 1.6 mm. Nia’s holes all pass; Tomos’s holes 3 and 4 fail.
| Dimension | Lower limit (mm) | Upper limit (mm) |
|---|---|---|
| Base length, 120 ± 0.5 | 119.5 | 120.5 |
| Base width, 60 ± 0.5 | 59.5 | 60.5 |
| Back height, 90 ± 0.5 | 89.5 | 90.5 |
| Slot width, 3.2 ± 0.1 | 3.1 | 3.3 |
| Sheet thickness, 3.0 ± 0.2 | 2.8 | 3.2 |
The tolerance band for the base length is 120.5 − 119.5 = 1.0 mm wide.
Every limit is nominal minus and plus the tolerance. The pupil sees that ± 0.5 gives a band of 1.0 mm, not 0.5 mm. Evidences criterion 1.
| Part | Reading | Length in mm | Difference | Accept or reject? |
|---|---|---|---|---|
| 1 | 120.2 mm | 120.2 | +0.2 | Accept |
| 2 | 119.8 mm | 119.8 | −0.2 | Accept |
| 3 | 120.6 mm | 120.6 | +0.6 | Reject (too long) |
| 4 | 12.04 cm | 12.04 × 10 = 120.4 | +0.4 | Accept |
| 5 | 119.4 mm | 119.4 | −0.6 | Reject (too short) |
| 6 | 120.0 mm | 120.0 | 0.0 | Accept |
| 7 | 120.5 mm | 120.5 | +0.5 | Accept (on the upper limit) |
| 8 | 120.3 mm | 120.3 | +0.3 | Accept |
| 9 | 121.0 mm | 121.0 | +1.0 | Reject (too long) |
| 10 | 120.1 mm | 120.1 | +0.1 | Accept |
Rejected: 3 out of 10. Percentage: 3 ÷ 10 × 100 = 30%.
(b) Limits 3.1 to 3.3 mm. A 3.15 accept · B 3.30 accept (on the upper limit) · C 3.05 reject (too narrow) · D 3.22 accept · E 3.34 reject (too wide).
The centimetre reading is converted before it is judged; left as 12.04 it would look wildly wrong. Parts on a limit are accepted, as the job sheet says. Comparing 3.05 with 3.1 needs care: 3.05 is smaller than 3.10. Evidences criteria 2 and 3.
(a) Total: 120.2 + 119.8 + 120.6 + 120.4 + 119.4 + 120.0 + 120.5 + 120.3 + 121.0 + 120.1 = 1,202.3 mm. Mean: 1,202.3 ÷ 10 = 120.23, so 120.2 mm to 1 decimal place.
(b) Range: 121.0 − 119.4 = 1.6 mm.
(c) The laser cutter is making parts slightly too long. The mean is about 0.2 mm above 120 mm, 7 of the 10 differences are positive, and 2 of the 3 rejects are too long. The range of 1.6 mm is also wider than the 1.0 mm tolerance band, so the parts vary too much as well.
The mean is worked out from the millimetre values, rounded correctly, and used with the signs of the differences to describe a pattern. Comparing the range with the tolerance band is a strong extra point. Evidences criterion 4.
| Hole | Should be | Nia | Nia accept? | Tomos | Tomos accept? |
|---|---|---|---|---|---|
| 1 | 30 | 30.0 | Accept (0.0) | 30.5 | Accept (+0.5) |
| 2 | 60 | 60.5 | Accept (+0.5) | 61.0 | Accept (+1.0, on the limit) |
| 3 | 90 | 89.5 | Accept (−0.5) | 91.5 | Reject (+1.5) |
| 4 | 120 | 120.5 | Accept (+0.5) | 122.0 | Reject (+2.0) |
Tomos measured each hole from the one before, so every 0.5 mm error was added to the last one: 0.5, then 1.0, then 1.5, then 2.0 mm. By the fourth hole the errors had added up to 4 × 0.5 = 2.0 mm, twice the tolerance. Nia measured every hole from the same datum edge, so each hole only has its own small error and the errors cannot build up.
Tomos’s positions are worked out by adding 30.5 each time (30.5, 61.0, 91.5, 122.0). The explanation names the key idea: chain measuring makes errors accumulate. Evidences criterion 5.
I checked all 10 bases against 120 mm ± 0.5 mm. 7 passed and 3 failed, so 30% of the batch was rejected. Two of the rejects were too long (120.6 mm and 121.0 mm) and one was too short (119.4 mm). The mean length was 120.2 mm, so the laser cutter is cutting about 0.2 mm too long on average. Before the next batch, the drawing or the cutter settings should be adjusted so the parts come out about 0.2 mm shorter, and the first part should be measured before the rest are cut.
Five sentences with the pass count, the percentage, the rejects, the mean and a specific action. Evidences criteria 3 and 4.
Worst cases: the thickest sheet (3.2 mm) will not fit the narrowest slot (3.1 mm): it is 0.1 mm too thick. The thinnest sheet (2.8 mm) in the widest slot (3.3 mm) leaves a 0.5 mm gap, so the back would wobble.
Accepted parts only: 120.2 + 119.8 + 120.4 + 120.0 + 120.5 + 120.3 + 120.1 = 841.3; 841.3 ÷ 7 = 120.19, so 120.2 mm.
45 mm ± 0.25 mm: limits 44.75 mm and 45.25 mm. 4.52 cm = 45.2 mm, so it passes.