Cover lesson · Design Technology · Year 9 · Intermediate

Checking parts against a tolerance

LNF: Numeracy → Learning about geometry helps us understand shape, space and position, and learning about measurement helps us quantify in the real world → Measurement

Name: Class: Date:

Cover teacher: you need no subject knowledge

What this practises: measuring in millimetres against a tolerance. GCSE Design and Technology (teaching from 2026) asks pupils in every pathway to “employ accurate measuring techniques and establish reference points or datum faces”, and to work within stated tolerances. Pupils work out upper and lower limits, check a batch of measured parts, convert centimetres to millimetres, find a mean and range, compare two ways of marking out, and write a short quality report. This is a numeracy lesson: everything is on paper and nobody uses tools today.

Print: this sheet, one per pupil. Pupils need a calculator and a ruler. No computers or workshop equipment are needed.

Run: 6 min read the job sheet together · 8 min Step 2, limits · 12 min Step 3, check the batch · 9 min Step 4, mean and range · 10 min Step 5, datum or chain · 10 min Step 6, the report, alone. Total 55 minutes.

Collect: this sheet. A check you can make: in Step 3(a) exactly 3 of the 10 bases should be rejected (parts 3, 5 and 9). Part 7 is exactly on the upper limit and is accepted.

What you are doing

No machine cuts every part to exactly the right size. A tolerance tells the maker how far from the drawing a part may be and still be accepted. A Year 9 class has laser cut a batch of 10 acrylic phone stands for the school summer fair. You are the quality controller: you will decide which parts pass, spot a pattern in the errors, and report back.

The job sheet

The phone stand has a flat base and a back that slots into it. All sizes are in millimetres (mm).

DimensionSize on the drawing (nominal)Tolerance
Base length120 mm± 0.5 mm
Base width60 mm± 0.5 mm
Back height90 mm± 0.5 mm
Slot width (the back fits into it)3.2 mm± 0.1 mm
Acrylic sheet thickness (from the supplier)3.0 mm± 0.2 mm

How to read a tolerance: 120 mm ± 0.5 mm means the part may be anything from 120 − 0.5 = 119.5 mm (the lower limit) to 120 + 0.5 = 120.5 mm (the upper limit). A part exactly on a limit is accepted.

Units: 1 cm = 10 mm, so 12.3 cm = 123 mm.

Step 1: read the job sheet

Read the job sheet with your partner. Underline the word nominal and the symbol ±. Say out loud what “90 mm ± 0.5 mm” means.

Step 2: work out the limits

DimensionLower limit (mm)Upper limit (mm)
Base length, 120 ± 0.5119.5120.5
Base width, 60 ± 0.5
Back height, 90 ± 0.5
Slot width, 3.2 ± 0.1
Sheet thickness, 3.0 ± 0.2

How wide is the whole tolerance band for the base length, from lower limit to upper limit?   mm

Step 3: check the batch

(a) These are the base lengths measured with digital callipers. One pupil wrote their reading in centimetres: convert it first. Work out the difference from 120 mm (use + for too long and − for too short), then write Accept or Reject.

PartReadingLength in mmDifference from 120 mmAccept or reject?
1120.2 mm120.2+0.2Accept
2119.8 mm
3120.6 mm
412.04 cm
5119.4 mm
6120.0 mm
7120.5 mm
8120.3 mm
9121.0 mm
10120.1 mm

Number rejected:   out of 10. Percentage rejected:   %

(b) Five slot widths were checked. Accept or reject each one using your limits from Step 2.

SlotABCDE
Width (mm)3.153.303.053.223.34
Accept or reject?

Step 4: look for a pattern

(a) Work out the mean base length of all 10 parts, in mm. Show your working and give your answer to 1 decimal place.

(b) Work out the range (longest minus shortest).

(c) Look at your differences in Step 3. Is the laser cutter making parts too long, too short, or neither? Use a figure.

Step 5: datum or chain?

A key rack needs 4 holes at 30, 60, 90 and 120 mm from the left-hand edge, which is the datum edge. The tolerance is ± 1.0 mm.

HoleShould be (mm)Nia (mm)Nia accept?Tomos (mm)Tomos accept?
13030.030.5
26060.5
39089.5
4120120.5

Tomos only made a 0.5 mm error each time. Explain why his last hole is so far out, and why measuring from a datum edge is better.

Step 6: the quality report

On your own. Write a short report (4 to 6 sentences) to the class teacher about the base parts. Say how many passed and what percentage failed, describe the pattern with the mean, and suggest what should change before the next batch.

Step by step

  1. 6 min Read the job sheet. Say what a tolerance means.
  2. 8 min Work out the upper and lower limits.
  3. 12 min Convert, compare and accept or reject every part.
  4. 9 min Find the mean and range and describe the pattern.
  5. 10 min Compare datum and chain measuring.
  6. 10 min Write the quality report on your own.

Success criteria

If you finish early