Cover lesson · Design Technology · Year 8 · Intermediate
LNF: Numeracy → Learning about geometry helps us understand shape, space and position, and learning about measurement helps us quantify in the real world → Angle
Name: Class: Date:
What this practises: numeracy in Design Technology. Pupils read a working drawing of an invented acrylic phone stand at scale 1:2. They change drawing lengths into real lengths, measure angles with a protractor, use angle facts, think of an angle as an amount of turn at a bend, find the mistakes in another pupil’s drawing, draw the stand to scale themselves and choose an angle for a tablet version. GCSE Design and Technology (teaching from 2026) expects pupils to understand working drawings, and this is the skill behind them.
Print: this sheet and the stimulus sheet “Llechen phone stand: working drawing”, one of each per pupil. Print the stimulus at actual size (100%), not “fit to page”: its check line must measure 50 mm. Pupils need a sharp pencil, a rubber, a 30 cm ruler and a protractor. No calculator is needed.
Run: 6 min Step 1, scale and lengths · 8 min Step 2, measuring angles · 6 min Step 3, angles as turns · 8 min Step 4, Elin’s drawing · 14 min Step 5, drawing to scale · 8 min Step 6, the tablet stand. Total 50 minutes.
Collect: this sheet, for the class teacher to check against the worked example.
Designers make a working drawing before anything is cut. It shows the exact lengths and angles, often at a scale so it fits the page. Today you will read the drawing of the Llechen phone stand, check it, draw it yourself and adapt it for a tablet.
(a) The drawing is at scale 1:2. Finish the sentence: “Every 1 mm on the drawing is …”
(b) Measure each part on the stimulus drawing to the nearest mm. Then work out the real length.
| Part | On the drawing (mm) | Working | Real length (mm) |
|---|---|---|---|
| Lip, L to J | |||
| Ledge, J to K | |||
| Back rest, K to T | |||
| Rear leg, T to R |
(c) The lip and ledge have real lengths on the stimulus. Do your answers match? If not, measure again.
Read the protractor box in section 3 of the stimulus. Estimate each angle first, then measure it.
| Angle | Estimate: acute, right or obtuse? | Measured (°) |
|---|---|---|
| a | ||
| b | ||
| c | ||
| d | ||
| e |
(a) Work out a + b. Why should it be this number? (Hint: look at the ledge and the table on both sides of K.)
(b) K, T and R make a triangle. Work out a + c + d. What should it be?
An angle measures an amount of turn. Imagine walking along the strip: down the lip from L to J, along the ledge to K, up the back rest to T, then down the rear leg to R. At each bend you turn. If the strip went straight on, you would not turn at all, so the turn is 180° minus the angle inside the bend.
| Bend | Angle inside the bend | Turn (180° − angle) |
|---|---|---|
| J | e = | |
| K | b = | |
| T | c = |
At which bend must the acrylic be turned the most? What does that mean for the person bending it?
Read section 4 of the stimulus.
(a) Which length is wrong? What should it be, and what mistake did Elin make?
(b) Which angle is wrong? What should it be? Explain how she misread the protractor.
(c) Give Elin one tip to check an angle before she draws it.
(a) Scale 1:2. Draw the whole side view in the box.
(b) Scale 1:1 (full size). The maker needs the bottom corner at full size. Draw the lip, the ledge and the first 50 mm of the back rest at their real lengths, with the same angles. Label it “Scale 1:1”.
Read section 5 of the stimulus.
(a) Which lean angle meets the specification? Give a reason for rejecting each of the others.
(b) The rear leg is still at 90° to the table. For your lean angle, work out angles b and c, and the turn at K.
(c) The back rest is 180 mm long. How long is it on a drawing at scale 1:2? At scale 1:4?
(d) In the box, draw the table, the tablet back rest at your lean angle and the rear leg, at scale 1:4.