Cover lesson · Design Technology · Year 7 · Beginner

Sequencing and punctuating a safe workshop manufacturing plan

LNF: Literacy → Writing → Connectives and syntax

Also assessed, DCF: Data and computational thinking → Problem solving and modelling

Name: Class: Date:

Cover teacher: you need no subject knowledge

What this practises: connectives, sentence syntax and punctuation in Design Technology, alongside algorithmic sequencing and production timing. Pupils put 8 jumbled workshop cards for making a line-bent acrylic key fob into logical manufacturing order, calculate the total production time including a 4-minute cooling wait, join each hazard to its safety precaution using precise connectives (before, while, so that, otherwise), and write a properly punctuated workshop manufacturing card.

Board: open the supply teacher presentation for board slides, timers and script: /cover-lesson-resources/presentations/sequencing-and-punctuating-a-safe-workshop-manufacturing-plan.html

Print: this worksheet (one per pupil) and the stimulus sheet “Line-bent acrylic key fob: jumbled workshop notes and hazard cards” (one between two). Pupils only need a pen.

Run: 5 min settling starter · 5 min sequence and connectives brief · 10 min Step 1 sequencing and timing · 10 min Step 2 hazard connectives · 12 min Step 3 punctuated manufacturing plan · 5 min Step 4 sequence check · 3 min plenary check. Total 50 minutes.

Collect: this worksheet at the end of the lesson. Keep the stimulus sheets for the next class.

Quick checks: Correct card order from Stage 1 to Stage 8: D (4 min) → G (6 min) → B (6 min) → H (5 min) → A (4 min) → E (2 min) → F (5 min) → C (4 min). Total manufacturing time = 36 minutes, leaving 6 minutes of buffer time out of 42 usable minutes in a 50-minute lesson.

What you are doing

A safe workshop manufacturing plan is like an algorithm: every step must happen in the right order, and every safety rule must be written clearly so nobody misreads it. Today you will sort 8 jumbled, unpunctuated notes for making a line-bent acrylic key fob into their correct sequence, calculate the total production time, join hazards to precautions using precise connectives, and write a clean, well-punctuated workshop card.

Step 1: Sequence the 8 workshop stages and calculate total time

Read Cards A to H in Section 2 of the stimulus sheet. Put them into the right manufacturing order (Stages 1 to 8) below, write the main tool or equipment used, record the time in minutes, and add up the total time. Stages 1 and 2 are done for you.

Stage no. Card letter (A to H) Short name of stage Main tool / equipment Time (min)
Stage 1 Card D Mark out cutting lines, bend line & hole centre Steel rule & felt-tip pen 4 min
Stage 2 Card G Saw waste corners just outside the line Coping saw & soft-jaw vice 6 min
Stage 3
Stage 4
Stage 5
Stage 6
Stage 7
Stage 8
Total production time (including the 4-minute cooling wait in Stage 8):

Step 2: Join each hazard to its precaution using connectives

Read Section 3 of the stimulus sheet. For each tool below, write one complete, properly punctuated sentence that joins the precaution to the hazard or reason using the required connective in bold. Row 1 is completed for you.

Tool / stage Required connective Complete safety sentence (start with a capital letter and end with a full stop)
1. Pillar drill before Clamp the flat acrylic blank tightly in a machine vice with scrap wood underneath and put on safety goggles before switching on the pillar drill.
2. Strip heater (160°C) while
3. Coping saw & vice so that
4. Film & cooling jig otherwise

Step 3: Write the punctuated 8-stage workshop manufacturing card

Rewrite the unpunctuated notes from Cards A to H in their correct sequence (Stages 1 to 8) as a clear workshop card. Every stage must start with an imperative verb and a capital letter, use commas and full stops accurately, and include a connective (such as before, while, until, so that or otherwise).

Stage 1 (worked example): Check the 90 mm by 35 mm acrylic blank, then use a steel rule and felt-tip pen to mark the curved corners, the bend line and the hole centre on the protective film so that the glossy surface is not scratched.

Stage 2 (Coping saw):

Stage 3 (Flat hand file):

Stage 4 (Wet-and-dry paper):

Stage 5 (Pillar drill):

Stage 6 (Peeling protective film):

Stage 7 (Strip heater):

Stage 8 (Cooling jig):

Step 4: Explain sequence logic and check workshop timing

(a) Using at least two connectives from today’s lesson, explain why Stage 6 (peeling off the protective plastic film) must happen after filing and drilling (Stages 3 to 5), but before heating on the strip heater (Stage 7).

(b) A Design Technology lesson lasts 50 minutes, and pupils need 8 minutes for the register, getting aprons/goggles and tidying away tools. Calculate how many usable making minutes are available, and state how many minutes of spare buffer time remain after completing your 36-minute manufacturing plan.

Step by step

  1. 5 min Write your name, class and date, read Section 1 of the stimulus sheet, and answer the starter question.
  2. 5 min Review the workshop sequence and the 4 safety connectives (before, while, so that, otherwise) on the board.
  3. 10 min Complete Step 1 to put Cards A to H in order (Stages 1 to 8) and calculate the total production time.
  4. 10 min Complete Step 2 to write complete safety sentences using the 4 required connectives.
  5. 12 min Complete Step 3 to write the punctuated 8-stage manufacturing card starting each step with an imperative verb.
  6. 5 min Complete Step 4 to explain why Stage 6 sits between drilling and heating, and calculate the lesson buffer time.
  7. 3 min Check your answers against the board and tick the success criteria below.

Success criteria

If you finish early