LNF Cymru Literacy and numeracy for Wales

← All qualifications

VCSE Built Environment

VCSE Built Environment asks learners to read a Welsh case study and technical documents such as briefs and risk assessments, to justify choices of sites, methods and materials in writing, and to evaluate their own practical work using accurate trade terms. Its numeracy is mostly practical and sits in the 60% Unit 3, with accurate measuring to tolerances, reading plans and drawings, mixing to ratios and estimating quantities, alongside cost, time and carbon comparisons and project timelines in Unit 2. The single biggest thing KS3 should build is accurate measuring and marking out in millimetres from a drawing, checked against a stated tolerance.

Awarding body
WJEC
Level
Level 1 and Level 2
First taught
September 2027
Amount of literacy work
Medium
Amount of numeracy work
Medium
Specification
Open the specification
How this qualification is assessed
  • Unit 1: Introduction to the Built Environment Sector: Examination (sector test) 1 hour, 50 marks, 20%, set and marked by WJEC, paper-based or on-screen
  • Unit 2: The Built Environment in Focus: NEA 6 hours 30 minutes, 50 marks, 20%, set and marked by WJEC, tasks based on a case study released each year on Portal
  • Unit 3: Skills Development and Demonstration: NEA 14 hours, 90 marks, 60%, set by WJEC, marked by the centre and moderated by WJEC, practical tasks in three chosen trades plus an evaluation

Skills that use Measurement

  1. Measuring, marking out and working to tolerances

    Assessed: In coursework (non-examination assessment, NEA)

    Learners must measure and mark out accurately with tools such as a tape measure, spirit level, chalk line or laser level, and follow dimensions and tolerances in every trade activity. Work must be level, plumb and square, and is checked at each stage to find and correct errors.

    Numeracy: Measurement, Angle, The number system, Strategic competence, Communicating with symbols

    Getting pupils ready

    Year 7
    Pupils measure and mark a piece of card or timber to the nearest millimetre with a steel rule, then check a partner's marks.
    Year 8
    Pupils use a spirit level and tape measure to check whether shelves and window sills around school are level, recording readings in millimetres and converting them to centimetres and metres.
    Year 9
    Pupils make a simple frame from a drawing with a tolerance of plus or minus 2 mm, measure the finished piece, and record whether each dimension is within the upper and lower limits.
    Show the specification wording and the LNF statements

    Where it is in the specification: Unit 3, Section 3.3.1, page 37; Section 3.2.2, page 36

    “follow instructions, dimensions, and tolerances accurately in all practical trade activities”
    Progression step 3

    • I can read and interpret scales or divisions on a range of measuring instruments.

    • I can record measurements in different ways, e.g. 1.3kg = 1kg 300g, 4.2cm = 4cm 2mm.

    • I can convert metric units of length to smaller units, e.g. cm to mm, m to cm, km to m.

    Progression step 4

    • I can read and interpret scales on a range of measuring instruments.

    • I can use the common units of measure, convert between related units of the metric system and carry out calculations.

    • I can measure and draw angles.

    Progression step 5

    • I can recognise and define limitations on accuracy of measurements, e.g. upper and lower bounds.

    • I can identify, measure or obtain required information to complete the task.

    • I can use appropriate notation, symbols and units of measurement, including compound measures.

  2. Planning time, order of work and critical paths

    Assessed: In coursework (non-examination assessment, NEA)

    Learners must evaluate project plans, including order of operations, critical paths and bottlenecks, and a project timeline is a design consideration in Unit 1. In Unit 3 they sequence activities logically and recognise time limits when planning trade tasks.

    Numeracy: Measurement, Strategic competence, Logical reasoning

    Getting pupils ready

    Year 7
    Pupils use a calendar to plan a two week class project with five tasks and work out the new finish date if one task takes two extra days.
    Year 8
    Pupils draw a timeline for building a garden wall that shows which tasks can happen at the same time, and calculate the shortest total time.
    Year 9
    Pupils are given task times and dependencies for a small extension, find the critical path and total duration, and work out the effect of a three day delay to the roof.
    Show the specification wording and the LNF statements

    Where it is in the specification: Unit 2, Section 2.3.2, page 25; Unit 1, Section 1.2.3, page 15; Unit 3, Section 3.2.1, page 35

    “critical paths and bottlenecks”
    Progression step 3

    • I can use and interpret calendars, timetables and schedules to plan events and activities, and make calculations as part of the planning journey.

    • I can prioritise and organise the relevant steps needed to complete the task or reach a solution.

    Progression step 4

    • I can prioritise and organise the relevant steps needed to complete the task or reach a solution.

    • I can select, trial and evaluate a variety of possible approaches and break complex problems into a series of tasks.

    Progression step 5

    • I can prioritise and organise the relevant steps needed to complete the task or reach a solution.

    • I can justify my procedures, predictions and conjectures.

Good to know

Links with other qualifications

Measuring to tolerances, reading scale plans and working out quantities overlap with GCSE Design and Technology and Mathematics and Numeracy, and land use, population and housing need overlap with GCSE Geography.

Source: WJEC Level 1/Level 2 VCSE Built Environment specification, approved by Qualifications Wales, teaching from September 2027, for award from 2029 (© WJEC CBAC Ltd 2026).