LNF Cymru Literacy and numeracy for Wales

← All qualifications

Foundation Design and Technology

Foundation Design and Technology is a two year Entry Level and Level 1 course for learners aged 14 to 16, taken in Engineering Design, Fashion and Textiles or Product Design. Literacy runs through both units: the Unit 1 topic tests use objective and short answer questions full of technical vocabulary on safety, materials and processes, and the Unit 2 design project asks learners to analyse an existing product, write a design brief and specification, annotate and present ideas and evaluate their prototype. Numeracy is lighter and practical: setting sizes in the specification, measuring and drawing accurately, planning time across a 40 hour project and, in Engineering Design, knowing volts, amps and ohms. KS3 should build clear technical writing alongside accurate measuring in millimetres.

Awarding body
WJEC
Level
Entry Level and Level 1
First taught
September 2027
Amount of literacy work
Medium
Amount of numeracy work
Low
Specification
Open the specification
How this qualification is assessed
  • Unit 1: Design and Technology in the 21st Century: Three topic tests of 20 minutes each (1 hour in total): a Core Knowledge and Understanding test on health and safety (16 marks) and two pathway tests on Materials and Components and on Tools, Techniques and Processes (12 marks each), 40 marks, 30%, set and marked by WJEC, digital or paper format within a four week window
  • Unit 2: Design Project: Non-examination assessment, a sustained design and make task of approximately 40 hours based on a contextual challenge set by the centre, 60 marks, 70%, set and marked by the centre and moderated by WJEC

Skills that use Connectives and syntax

  1. Evaluating design ideas and the final prototype

    Assessed: In coursework (non-examination assessment, NEA)

    Learners make evaluations of their initial design solutions and produce an evaluation of their final prototype, judging how well it meets the needs and wants of the user and whether it is fit for purpose. AO4, analyse and evaluate products and solutions, carries 20% of the qualification, all of it in Unit 2.

    Literacy: Planning and organising for different purposes, audiences and context, Connectives and syntax

    Getting pupils ready

    Year 7
    Pupils write three sentences about their finished product: one thing that went well, one that did not and what they would change next time.
    Year 8
    Pupils write a paragraph evaluating their product against two specification points, using connectives such as because, however and as a result.
    Year 9
    Pupils write a structured evaluation that checks each specification point, quotes a user's comment and ends with two realistic improvements.
    Show the specification wording and the LNF statements

    Where it is in the specification: Unit 2, Section 2.1.5, page 22; Section 3.1, page 24

    “produce an evaluation of their final prototype.”
    Progression step 3
    • I can write an effective introduction that establishes context and purpose, a suitable balance between facts and viewpoints, and a precise conclusion.

    • I can use an increasing range of connectives to organise my ideas in sentences, paragraphs and whole texts.

    Progression step 4
    • I can use summary, discussion of issues, detailed explanations and logic when covering a topic.

    • I can use a range of connectives specifically when organising my ideas in whole texts for different purposes.

Good to know

Links with other qualifications

The specification says the qualification "provides a broad basis for progression onto GCSE Design and Technology" (page 8). The Foundation shares the GCSE's design brief, specification, annotation and evaluation writing and its technical vocabulary, but tests knowledge through short answer topic tests rather than extended written answers. GCSE Design and Technology steps up the numeracy, with measuring to tolerances, estimating material quantities, waste and costs, using collated data to set specification criteria, scale drawing and, in Engineering Design, mechanical and electronic calculations. Accurate measuring and unit work also link with GCSE Mathematics and Numeracy.

Source: WJEC Entry Level/Level 1 Foundation Design and Technology specification, approved by Qualifications Wales, teaching from September 2027, for award from 2029 (© WJEC CBAC Ltd 2026).