GCSE Design and Technology
Learners type short and extended answers in an on-screen examination. In a 40 hour design project worth 70% they write a design brief and specification, annotate and justify ideas, and evaluate their prototype using feedback from users. Numeracy is practical and constant: accurate measuring and marking out within tolerances in every pathway, costing and material estimates in Fashion and Textiles, and formula-based mechanical and electronic calculations in Engineering Design. The single biggest thing Key Stage 3 should build is precise measuring in millimetres against a stated tolerance, followed by a written evaluation that uses test results and user comments as evidence.
- Awarding body
- WJEC
- Level
- Level 1 and Level 2
- First taught
- September 2026
- Amount of literacy work
- Medium
- Amount of numeracy work
- Medium
- Specification
- Open the specification
How this qualification is assessed
- Unit 1: Design and Technology in the 21st Century: Digital (on-screen) examination 1 hour 30 minutes, 30%, 80 marks
- Unit 2: Design Project: Non-examination assessment, approximately 40 hours, 70%, 100 marks
Skills that use Logical reasoning
-
Mechanical and electronic calculations (Engineering Design)
Engineering Design learners must calculate Ohm's law, potential dividers, rotational velocity for pulleys and gears, velocity ratio, mechanical advantage and moments in lever systems, using units such as volts, amps and ohms.
Numeracy: Calculation, Communicating with symbols, Measurement, Fluency, Logical reasoning
Getting pupils ready
- Year 7
- Pupils count the teeth on two gears in a gear kit, write the ratio in its simplest form, and predict then check how many turns the driven gear makes.
- Year 8
- Pupils measure the lever in a moving toy, use effort times distance equals load times distance to predict the load it can lift, and test the prediction.
- Year 9
- Pupils build a simple LED circuit, measure voltage and current with a multimeter, and use V = I × R to calculate and choose a suitable resistor.
Show the specification wording and the LNF statements
Where it is in the specification: Unit 1, 1.1.9 and 1.1.10 (Engineering Design pathway), pages 17 to 18
“recognise the relationships between voltage, current and resistance and calculate ohms law”
Progression step 3
I can use ratio and proportion to calculate quantities.
I can multiply 2- and 3-digit numbers by a 2-digit number.
I can use appropriate notation, symbols and units of measurement.
Progression step 4
I can demonstrate an understanding of the relationship between a formula representing a measurement and the units used.
I can use ratio and proportion including map scales.
I can use the order of operations including brackets and powers.
Progression step 5
I can use appropriate notation, symbols and units of measurement, including compound measures.
I can use a scientific calculator effectively and efficiently to carry out calculations using the available range of function keys.
I can explain results and procedures precisely using appropriate mathematical language.
Good to know
- Unit 1 is typed on screen, not handwritten: "Digital examination: 1 hour 30 minutes" (Summary of assessment, page 4).
- The specification does not mention marks for spelling, punctuation and grammar. The four assessment objectives cover knowledge, application, developing designs and analysing and evaluating, and "The Assessment Pack will include all detailed information relating to assessment." (Assessment, page 43).
- The specification does not say whether a calculator is allowed in the on-screen examination, although Engineering Design learners must "calculate ohms law" (Unit 1, 1.1.9, page 17). Check the Assessment Pack.
- Formula-based calculations are for one pathway only: "This area of study is relevant to learners that have chosen Engineering Design as their pathway." (Unit 1, 1.1(a), page 14). Costing from standard fabric widths sits in Fashion and Textiles (Unit 1, 1.1.18, page 23).
- The design project is "Non-examination assessment: Approximately 40 hours", worth 70% and 100 marks (page 4). AO4, analyse and evaluate, is 20% of the qualification and is assessed only in Unit 2 (page 43).
- Written notes, presentations and mathematical modelling are listed "for example" (Unit 2, 2.1.4, pages 34 to 35), which the specification says "indicates that the specified content is for guidance only" (page 8). No word limits are stated.
Links with other qualifications
Ohm's law and moments overlap with The Sciences, gear ratios, scale drawing and tolerances with Mathematics and Numeracy, and product analysis and evaluative writing with English Language and Literature, so shared methods and vocabulary would help pupils.
Source: WJEC GCSE Design and Technology specification, Approved by Qualifications Wales, teaching from 2026, for award from 2028 (© WJEC CBAC Ltd 2025).