Foundation Design and Technology
Mae disgrifiad y cymhwyster yn Saesneg yn unig, gan ei fod wedi ei gymryd o fanyleb Saesneg CBAC.
Foundation Design and Technology is a two year Entry Level and Level 1 course for learners aged 14 to 16, taken in Engineering Design, Fashion and Textiles or Product Design. Literacy runs through both units: the Unit 1 topic tests use objective and short answer questions full of technical vocabulary on safety, materials and processes, and the Unit 2 design project asks learners to analyse an existing product, write a design brief and specification, annotate and present ideas and evaluate their prototype. Numeracy is lighter and practical: setting sizes in the specification, measuring and drawing accurately, planning time across a 40 hour project and, in Engineering Design, knowing volts, amps and ohms. KS3 should build clear technical writing alongside accurate measuring in millimetres.
- Corff dyfarnu
- CBAC
- Lefel
- Entry Level and Level 1
- Addysgu gyntaf
- Medi 2027
- Faint o waith llythrennedd
- Canolig
- Faint o waith rhifedd
- Isel
- Manyleb
- Agor y fanyleb
Sut mae'r cymhwyster hwn yn cael ei asesu
- Unit 1: Design and Technology in the 21st Century: Three topic tests of 20 minutes each (1 hour in total): a Core Knowledge and Understanding test on health and safety (16 marks) and two pathway tests on Materials and Components and on Tools, Techniques and Processes (12 marks each), 40 marks, 30%, set and marked by WJEC, digital or paper format within a four week window
- Unit 2: Design Project: Non-examination assessment, a sustained design and make task of approximately 40 hours based on a contextual challenge set by the centre, 60 marks, 70%, set and marked by the centre and moderated by WJEC
Y sgiliau llythrennedd a rhifedd yn y cymhwyster hwn
-
Answering short answer questions in the topic tests
The Unit 1 topic tests use multiple choice, objective and short answer questions, so learners need to read each question carefully and write brief, accurate answers. They are asked to identify and describe, for example, hazards, the suitability of materials and the advantages and disadvantages of CAD/CAM.
Llythrennedd: Strategaethau darllen, Geirfa, sillafu, gramadeg
Paratoi disgyblion
- Blwyddyn 7
- Pupils read a question about PPE, underline the command word such as name, state or describe, and write a one sentence answer.
- Blwyddyn 8
- Pupils answer five short questions on safety signs and materials, then compare their answers with a mark scheme and add any missing technical word.
- Blwyddyn 9
- Pupils complete a timed practice topic test with short answers that describe the suitability of a material, using because to link each property to the product.
Dangos geiriad y fanyleb a datganiadau'r Fframwaith Llythrennedd a Rhifedd
Ble mae yn y fanyleb: Section 3.2, page 25; Unit 1, Sections 1.1.1 to 1.1.7, pages 12 to 18
“multiple choice questions (MCQ), objective test questions (OTQ) and short answer questions”
Cam cynnydd 3
Rwy'n gallu defnyddio ystod o strategaethau er mwyn dod o hyd i wybodaeth, e.e. cip ddarllen (sgimio) am yr hanfodion, llithr ddarllen (sganio) am fanylion.
Rwy'n gallu defnyddio geirfa amrywiol, briodol a manwl gywir, gan gynnwys geiriau sy'n benodol i faes dysgu a phrofiad/disgyblaeth at ddibenion gwahanol.
Cam cynnydd 4
Rwy'n gallu defnyddio ystod o strategaethau, e.e. darllen cyflym, darllen agos, anodi, rhagfynegi, i gip ddarllen (sgimio) testunau i gael yr hanfodion, y syniadau a’r themâu allweddol, a’u llithr ddarllen (sganio) am wybodaeth fanwl.
Rwy’n gallu gwneud dewisiadau gwybodus am eirfa, iaith idiomatig a ffigurol, a chystrawen er mwyn mynegi fy hun yn rhugl, yn gywir ac yn eglur.
-
Technical vocabulary for materials, tools and processes
Each pathway brings a large set of technical terms, such as ferrous, thermoforming, photochromic, overlocker, darts, vacuum forming and batch production. Learners must know and use these words in the Unit 1 topic tests and in the annotations and evaluations of their design project.
Llythrennedd: Geirfa, sillafu, gramadeg
Paratoi disgyblion
- Blwyddyn 7
- Pupils match pictures of workshop tools and textile equipment to their names and learn five spellings, such as aluminium and scissors, in a word check.
- Blwyddyn 8
- Pupils sort materials into hardwoods, softwoods, ferrous metals, non-ferrous metals and plastics, writing one sentence about a property of each.
- Blwyddyn 9
- Pupils annotate a photo of a finished product using at least six technical terms correctly, such as thermoforming, batch production and surface finish.
Dangos geiriad y fanyleb a datganiadau'r Fframwaith Llythrennedd a Rhifedd
Ble mae yn y fanyleb: Unit 1, Sections 1.1.2 to 1.1.7, pages 13 to 18
“the physical characteristics of thermoforming and thermosetting plastics”
Cam cynnydd 3
Rwy'n gallu defnyddio geirfa amrywiol, briodol a manwl gywir, gan gynnwys geiriau sy'n benodol i faes dysgu a phrofiad/disgyblaeth at ddibenion gwahanol.
Rwy'n gallu defnyddio strategaethau i sillafu geiriau amlsillafog, cymhleth ac afreolaidd yng nghyd-destun pob maes dysgu a phrofiad.
Cam cynnydd 4
Rwyf wedi cael profiad o ystod o eirfa sy'n benodol i faes dysgu a phrofiad/disgyblaeth a geirfa academaidd gyffredinol, ac yn gallu ei defnyddio wrth i mi gyfathrebu.
Rwy'n gallu defnyddio amrywiaeth o strategaethau ac adnoddau i sillafu geirfa gyfarwydd ac anghyfarwydd a geiriau sy'n benodol i faes dysgu a phrofiad/disgyblaeth yn gywir.
-
Describing hazards, safety signs and safe working practices
All learners take a health and safety topic test covering PPE, safety signs and hazard symbols, manual handling and electrical safety. They must identify and describe hazards and safe working practices as part of risk assessment, reading signs and symbols and explaining them in words.
Llythrennedd: Deall, ymateb a dadansoddi, Cynllunio a threfnu ar gyfer gwahanol ddibenion, cynulleidfaoedd a chyd-destunau
Paratoi disgyblion
- Blwyddyn 7
- Pupils read the safety signs around the workshop and write what each one means and which colour group it belongs to.
- Blwyddyn 8
- Pupils write a simple risk assessment for the pillar drill, describing two hazards and the safe working practice for each in full sentences.
- Blwyddyn 9
- Pupils read a manufacturer's safety sheet for a hot glue gun or sewing machine and write a short risk assessment that names the hazards, who is at risk and how to work safely.
Dangos geiriad y fanyleb a datganiadau'r Fframwaith Llythrennedd a Rhifedd
Ble mae yn y fanyleb: Unit 1, Section 1.1.1, page 12
“Learners should be able to identify and describe risk assessment procedures”
Cam cynnydd 3
Rwy'n gallu darllen yn fanwl, gan adnabod a nodi nodweddion testunau, e.e. cyflwyniad, dilyniant, darluniau, ffurfioldeb, geirfa allweddol.
Rwy'n gallu defnyddio ac addasu gwahanol strwythurau yn fy ngwaith ysgrifennu, e.e. adroddiad ar ddigwyddiad, ymchwiliad neu arbrawf.
Cam cynnydd 4
Rwy'n gallu darllen yn fanwl, gwneud gwaith dilynol a defnyddio deunyddiau ychwanegol mewn testunau i ymestyn fy nealltwriaeth.
Rwy'n gallu addasu fy arddull ysgrifennu, gan ddewis a defnyddio'r strwythurau gorau ar gyfer gwahanol gyd-destunau a dibenion, e.e. i ddisgrifio, esbonio, darbwyllo, trafod yn llwyddiannus.
-
Analysing existing products and the work of designers
In Unit 2 learners explore and investigate existing products and the work of design professionals, and analyse and evaluate an existing product relevant to their own design work. This means reading product information and reviews and pulling out what matters for their own users.
Llythrennedd: Deall, ymateb a dadansoddi
Paratoi disgyblion
- Blwyddyn 7
- Pupils look at an existing torch and its packaging and write down who it is for, what it does and what it is made from.
- Blwyddyn 8
- Pupils read two product reviews of the same backpack and summarise what users like and dislike about it.
- Blwyddyn 9
- Pupils analyse an existing product related to their project using the maker's website, reviews and their own handling of it, then write which features they will use or improve.
Dangos geiriad y fanyleb a datganiadau'r Fframwaith Llythrennedd a Rhifedd
Ble mae yn y fanyleb: Unit 2, Section 2.1.1, page 20; Unit 2, Section 2.1.3, page 21
“analyse and evaluate an existing product that is relevant to their own design work”
Cam cynnydd 3
Rwy'n gallu defnyddio ffynonellau cyfeirio/digidol i ddewis, crynhoi a chyfuno gwybodaeth, gan gyfeirio atyn nhw fel y bo'n briodol.
Rwy'n gallu coladu a gwneud cysylltiadau, e.e blaenoriaethu, categoreiddio, rhwng gwybodaeth a syniadau o wahanol ffynonellau gan gynnwys testunau digidol a chlyweledol.
Cam cynnydd 4
Rwy'n gallu ymchwilio i amrywiaeth eang o ffynonellau cyfeirio a digidol er mwyn datblygu dealltwriaeth lawn o bwnc neu fater.
Rwy'n gallu crynhoi, cyfuno a dadansoddi gwybodaeth er mwyn magu dealltwriaeth fanwl, e.e. o achosion, canlyniadau, patrymau, gan ddefnyddio gwahanol ffynonellau.
-
Writing a design brief and specification
Learners write a design brief that explains the function of a product and the needs, wants and values of the intended users, then write specification points from their own research, covering function, user needs and the sizes of key features. This is part of the Unit 2 design project.
Llythrennedd: Cynllunio a threfnu ar gyfer gwahanol ddibenion, cynulleidfaoedd a chyd-destunau
Paratoi disgyblion
- Blwyddyn 7
- Pupils write a two sentence design brief for a phone stand, saying who it is for and what it must do.
- Blwyddyn 8
- Pupils turn notes from a short user interview into specification points under headings such as function, user and size.
- Blwyddyn 9
- Pupils write a full design brief and specification for their own project, check that each point is clear and can be tested, and redraft the ones that are not.
Dangos geiriad y fanyleb a datganiadau'r Fframwaith Llythrennedd a Rhifedd
Ble mae yn y fanyleb: Unit 2, Section 2.1.2, page 20
“write a design brief to explain the function of a product”
Cam cynnydd 3
Rwy'n gallu defnyddio ac addasu gwahanol strwythurau yn fy ngwaith ysgrifennu, e.e. adroddiad ar ddigwyddiad, ymchwiliad neu arbrawf.
Rwy'n gallu ystyried ffyrdd gwahanol o gynllunio, drafftio a chyflwyno fy ngwaith yn briodol.
Cam cynnydd 4
Rwy'n gallu addasu fy arddull ysgrifennu, gan ddewis a defnyddio'r strwythurau gorau ar gyfer gwahanol gyd-destunau a dibenion, e.e. i ddisgrifio, esbonio, darbwyllo, trafod yn llwyddiannus.
Rwy’n gallu dewis a defnyddio strategaethau priodol er mwyn cynllunio a datblygu fy ngwaith ysgrifennu at wahanol ddibenion ac ar gyfer gwahanol gynulleidfaoedd.
-
Annotating ideas and presenting the final design
Learners communicate and record their ideas with annotated sketches and drawings, develop them iteratively and present their final design with details that support manufacturing. Annotations need to explain choices clearly; the specification states that written evidence is annotated against the marking criteria and that presentations are recorded on observation records.
Llythrennedd: Cynllunio a threfnu ar gyfer gwahanol ddibenion, cynulleidfaoedd a chyd-destunau, Eglurder a geirfa
Paratoi disgyblion
- Blwyddyn 7
- Pupils add three labels to a sketch of their idea, each naming a feature and saying why it is there.
- Blwyddyn 8
- Pupils annotate two design ideas using sentence starters such as this suits the user because, then explain their favourite idea to a partner.
- Blwyddyn 9
- Pupils present their final design to a small group for two minutes, explaining materials, sizes and how it will be made, using their annotated drawing as a prompt.
Dangos geiriad y fanyleb a datganiadau'r Fframwaith Llythrennedd a Rhifedd
Ble mae yn y fanyleb: Unit 2, Section 2.1.3, page 21; Section 3.3, page 26
“communicate and record their ideas using appropriate techniques”
Cam cynnydd 3
Rwy'n gallu ystyried ffyrdd gwahanol o gynllunio, drafftio a chyflwyno fy ngwaith yn briodol.
Rwy'n gallu mynegi materion a syniadau'n glir gan ddefnyddio geirfa sy'n benodol i faes dysgu a phrofiad/disgyblaeth ac enghreifftiau.
Cam cynnydd 4
Rwy'n gallu defnyddio crynodebau, trafod materion, rhoi esboniadau manwl a defnyddio rhesymeg wrth ymdrin â phwnc.
Rwy’n gallu siarad yn glir, gan ddewis ac addasu fy iaith yn briodol ar gyfer ystod o gynulleidfaoedd a dibenion, a chan gyfleu ystyr yn effeithiol i’r gynulleidfa.
-
Evaluating design ideas and the final prototype
Learners make evaluations of their initial design solutions and produce an evaluation of their final prototype, judging how well it meets the needs and wants of the user and whether it is fit for purpose. AO4, analyse and evaluate products and solutions, carries 20% of the qualification, all of it in Unit 2.
Llythrennedd: Cynllunio a threfnu ar gyfer gwahanol ddibenion, cynulleidfaoedd a chyd-destunau, Cysyllteiriau a chystrawen
Paratoi disgyblion
- Blwyddyn 7
- Pupils write three sentences about their finished product: one thing that went well, one that did not and what they would change next time.
- Blwyddyn 8
- Pupils write a paragraph evaluating their product against two specification points, using connectives such as because, however and as a result.
- Blwyddyn 9
- Pupils write a structured evaluation that checks each specification point, quotes a user's comment and ends with two realistic improvements.
Dangos geiriad y fanyleb a datganiadau'r Fframwaith Llythrennedd a Rhifedd
Ble mae yn y fanyleb: Unit 2, Section 2.1.5, page 22; Section 3.1, page 24
“produce an evaluation of their final prototype.”
Cam cynnydd 3
Rwy'n gallu ysgrifennu cyflwyniad effeithiol sy'n nodi'r cyd-destun a'r diben, gan gynnwys cydbwysedd addas rhwng ffeithiau a safbwyntiau, a chasgliad penodol.
Rwy'n gallu defnyddio amrywiaeth gynyddol o gysyllteiriau i drefnu fy syniadau mewn brawddegau, paragraffau a thestunau cyfan.
Cam cynnydd 4
Rwy'n gallu defnyddio crynodebau, trafod materion, rhoi esboniadau manwl a defnyddio rhesymeg wrth ymdrin â phwnc.
Rwy'n gallu defnyddio amrywiaeth o gysyllteiriau'n benodol wrth drefnu fy syniadau yn destunau cyfan at wahanol ddibenion.
-
Talking with users and responding to feedback
Learners identify the needs, wants and values of their intended users in Unit 2, which usually means asking users questions and listening to their answers. The specification also lists collaborating with others to understand the role of feedback in design thinking as a learning experience, and Appendix A maps speaking and listening to both units.
Llythrennedd: Gofyn cwestiynau, Gwrando i ddeall
Paratoi disgyblion
- Blwyddyn 7
- Pupils ask a partner three prepared questions about what they want from a lunch box and note the answers.
- Blwyddyn 8
- Pupils interview a younger pupil or family member about a product, using follow-up questions, and summarise what they heard in three points.
- Blwyddyn 9
- Pupils show their model to a user, ask for feedback, repeat the main comments back to check they have understood, and decide which ones to act on.
Dangos geiriad y fanyleb a datganiadau'r Fframwaith Llythrennedd a Rhifedd
Ble mae yn y fanyleb: Unit 2, Section 2.1.1, page 20; Opportunities for integration of learning experiences, page 23; Appendix A, page 32
“identify the needs, wants and values of the intended user(s)”
Cam cynnydd 3
Rwy'n gallu gofyn ac ateb cwestiynau, gan adeiladu ar syniadau pobl eraill mewn trafodaethau grŵp a'u datblygu.
Rwy’n gallu gwrando ar syniadau/cyflwyniadau pobl eraill, a deall y gallan nhw fod â safbwynt gwahanol i mi, er mwyn ymateb yn briodol.
Cam cynnydd 4
Rwy’n gallu gwrando ar safbwyntiau a syniadau gwahanol bobl ar bynciau amrywiol, gan eu defnyddio i lunio fy nghasgliadau fy hun.
Rwy’n gallu ymateb i safbwyntiau pobl eraill mewn ffordd hyderus a sensitif, gan grynhoi a gwerthuso'r hyn rwyf wedi ei glywed, ei ddarllen neu ei weld.
-
Measuring and working to sizes
Learners write specifications that include the sizes of key product features and components, then select materials and use equipment to make a prototype that is fit for purpose. Accurate measuring and marking out, in millimetres for wood, metal and plastics or with a tape measure for textiles, is needed throughout the making in Unit 2.
Rhifedd: Mesur, Cymhwysedd strategol
Paratoi disgyblion
- Blwyddyn 7
- Pupils mark out a 100 mm by 60 mm piece of card or wood with a steel rule and try square, then check each side is within 1 mm.
- Blwyddyn 8
- Pupils measure a hand or a phone to set the sizes for a product, converting between centimetres and millimetres and writing the sizes on a sketch.
- Blwyddyn 9
- Pupils measure their finished prototype against the sizes in their specification and record the difference for each key feature in a table.
Dangos geiriad y fanyleb a datganiadau'r Fframwaith Llythrennedd a Rhifedd
Ble mae yn y fanyleb: Unit 2, Sections 2.1.2 and 2.1.4, pages 20 and 21
“sizes of key product features and/or components.”
Cam cynnydd 3
Rwy'n gallu darllen a dehongli graddfeydd neu raniadau ar amrywiaeth o offerynnau mesur.
Rwy'n gallu trosi unedau metrig o hyd i unedau llai, e.e. cm i mm, m i cm, km i m.
Rwy'n gallu nodi, mesur neu gasglu'r wybodaeth sy'n ofynnol er mwyn cwblhau'r dasg.
Cam cynnydd 4
Rwy'n gallu darllen a dehongli graddfeydd ar amrywiaeth o offerynnau mesur.
Rwy'n gallu defnyddio'r unedau mesur cyffredin, trosi rhwng unedau cysylltiedig y system fetrig a chwblhau cyfrifiadau.
-
Drawing ideas in 2D and 3D and to scale
Learners may communicate their ideas with formal and informal 2D and 3D drawing, and present their final design with details that support manufacturing, such as sizes. Formal drawing needs accurate dimensions, angles and scale.
Rhifedd: Siâp a gofod, Dealltwriaeth gysyniadol, Ongl
Paratoi disgyblion
- Blwyddyn 7
- Pupils sketch a box-shaped product in 3D on isometric grid paper and label its length, width and height.
- Blwyddyn 8
- Pupils draw the front and side views of their idea at half size and an isometric view using 30 degree lines measured with a protractor.
- Blwyddyn 9
- Pupils produce a dimensioned working drawing of their final design at a stated scale, showing every size needed to make it.
Dangos geiriad y fanyleb a datganiadau'r Fframwaith Llythrennedd a Rhifedd
Ble mae yn y fanyleb: Unit 2, Section 2.1.3, page 21
“formal and informal 2d and/or 3d drawing”
Cam cynnydd 3
Rwy'n gallu defnyddio iaith fathemategol i ddisgrifio siapiau dau ddimensiwn a thri dimensiwn yn gywir.
Rwy'n gallu cynrychioli cysyniad mewn ffyrdd gwahanol, gan lifo rhwng cynrychioliadau gwahanol gan gynnwys rhai llafar, diriaethol, gweledol, digidol a haniaethol.
Cam cynnydd 4
Rwy'n gallu mesur a lluniadu onglau.
Rwy'n gallu cymhwyso dealltwriaeth o gyfeiriannau a graddfa i ddehongli mapiau a chynlluniau, ac i greu cynlluniau a lluniadau wrth raddfa.
-
Electrical units: volts, amps and ohms (Engineering Design)
Engineering Design learners know the measurements used in electronic circuits: voltage in volts, current in amps and resistance in ohms, with its symbol. This is tested in the Unit 1 pathway topic tests, and no calculation such as Ohm's law is listed.
Rhifedd: Cyfathrebu â symbolau, Mesur
Paratoi disgyblion
- Blwyddyn 7
- Pupils read the voltage printed on batteries and a power supply and write each value with its unit and symbol.
- Blwyddyn 8
- Pupils use a multimeter to measure the voltage across a bulb and the resistance of three resistors, recording each reading with the correct unit.
- Blwyddyn 9
- Pupils read resistor values from the colour code, check them with a multimeter, and explain why 0.22 kilohms is the same as 220 ohms.
Dangos geiriad y fanyleb a datganiadau'r Fframwaith Llythrennedd a Rhifedd
Ble mae yn y fanyleb: Unit 1, Section 1.1.3, page 14
“the following measurements within the electronical circuits:”
Cam cynnydd 3
Rwy'n gallu defnyddio nodiant, symbolau ac unedau mesur priodol.
Rwy'n gallu darllen a dehongli graddfeydd neu raniadau ar amrywiaeth o offerynnau mesur.
Cam cynnydd 4
Rwy'n gallu defnyddio nodiant, symbolau ac unedau mesur priodol, gan gynnwys mesurau cyfansawdd.
Rwy'n gallu darllen a dehongli graddfeydd ar amrywiaeth o offerynnau mesur.
-
Gathering and using user data
Learners identify user groups and their needs, wants and values, then write specifications derived from their own research. A short survey with a tally or bar chart is one way to collect and summarise this. Appendix A ticks only Developing Mathematical Proficiency for Unit 2, not the statistics strand, so this is light.
Rhifedd: Casglu data, Dehongli data
Paratoi disgyblion
- Blwyddyn 7
- Pupils use a tally chart to record which of three colours their class prefers for a pencil case and say which is most popular.
- Blwyddyn 8
- Pupils write a five question survey for a product, collect answers from ten people and draw a bar chart of one question.
- Blwyddyn 9
- Pupils survey their target users with closed and open questions, chart the results and use them to set measurable specification points, noting where the sample was too small to be sure.
Dangos geiriad y fanyleb a datganiadau'r Fframwaith Llythrennedd a Rhifedd
Ble mae yn y fanyleb: Unit 2, Sections 2.1.1 and 2.1.2, page 20; Appendix A, page 33
“write specifications that are derived from their own research”
Cam cynnydd 3
Rwy'n gallu casglu data perthnasol i ateb cwestiynau a ofynnwyd.
Rwy'n gallu dod i gasgliadau o ddata ac rwy'n cydnabod y gall rhai casgliadau fod yn gamarweiniol neu'n ansicr.
Cam cynnydd 4
Rwy'n gallu casglu fy nata fy hun ar gyfer arolwg, e.e. drwy lunio holiadur.
Rwy'n gallu dod i gasgliadau o ddata ac rwy'n cydnabod y gall rhai casgliadau fod yn gamarweiniol neu'n ansicr.
-
Planning steps and time for making
Learners plan and manage each step of making their prototype within a design and make task of about 40 hours, so they need to order the steps and estimate and track time. Appendix A maps planning and organisation and Developing Mathematical Proficiency to Unit 2.
Rhifedd: Cymhwysedd strategol, Mesur
Paratoi disgyblion
- Blwyddyn 7
- Pupils put the steps for making a simple product in order and estimate in minutes how long each will take.
- Blwyddyn 8
- Pupils make a timed plan across four lessons, record the actual time for each step and work out the difference from their estimate.
- Blwyddyn 9
- Pupils build a week by week plan for their project, review progress each week and reschedule the remaining steps so they still finish on time.
Dangos geiriad y fanyleb a datganiadau'r Fframwaith Llythrennedd a Rhifedd
Ble mae yn y fanyleb: Unit 2, Section 2.1.4, page 21; Section 3.2, page 26; Appendix A, page 33
“plan and manage each step of the manufacturing process”
Cam cynnydd 3
Rwy'n gallu blaenoriaethu a threfnu'r camau perthnasol sydd eu hangen i gwblhau'r dasg neu ddod o hyd i ddatrysiad.
Rwy'n gallu defnyddio a dehongli calendrau, amserlenni a rhaglenni i gynllunio digwyddiadau a gweithgareddau, a gwneud cyfrifiadau fel rhan o'r daith gynllunio.
Cam cynnydd 4
Rwy'n gallu blaenoriaethu a threfnu'r camau perthnasol sydd eu hangen i gwblhau'r dasg neu ddod o hyd i ddatrysiad.
Rwy'n gallu dewis, treialu a gwerthuso amrywiaeth o ddulliau posibl a rhannu problemau cymhleth yn gyfres o dasgau.
Da gwybod
- Unit 1 questions are short: the topic tests use "multiple choice questions (MCQ), objective test questions (OTQ) and short answer questions" and can be sat on paper or on screen (Section 3.2, page 25).
- No marks for spelling, punctuation and grammar are mentioned; all marks sit under AO1 to AO4 (Section 3.1, page 24), and "The Assessment Pack will include all detailed information relating to assessment." (page 24).
- Writing in Unit 2 is marked through annotation: "Written evidence must be annotated to show how it meets the marking criteria." (Section 3.3, page 26).
- Spoken work such as presentations is evidenced by the teacher: performance evidence "must be documented using observation records" (Section 3.3, page 26).
- Numeracy is not named in the content, and calculations are not listed; Engineering Design learners only need to know "the following measurements within the electronical circuits:" volts, amps and ohms (Unit 1, page 14).
- Appendix A (pages 32 and 33) ticks Listening, Reading, Speaking and Writing for both units, but ticks only "Developing Mathematical Proficiency" for Unit 2 and none of the number, geometry and measurement or statistics strands.
Cysylltiadau â chymwysterau eraill
The specification says the qualification "provides a broad basis for progression onto GCSE Design and Technology" (page 8). The Foundation shares the GCSE's design brief, specification, annotation and evaluation writing and its technical vocabulary, but tests knowledge through short answer topic tests rather than extended written answers. GCSE Design and Technology steps up the numeracy, with measuring to tolerances, estimating material quantities, waste and costs, using collated data to set specification criteria, scale drawing and, in Engineering Design, mechanical and electronic calculations. Accurate measuring and unit work also link with GCSE Mathematics and Numeracy.
Ffynhonnell: WJEC Entry Level/Level 1 Foundation Design and Technology specification, approved by Qualifications Wales, teaching from September 2027, for award from 2029 (© WJEC CBAC Ltd 2026).