Foundation Design and Technology
Mae disgrifiad y cymhwyster yn Saesneg yn unig, gan ei fod wedi ei gymryd o fanyleb Saesneg CBAC.
Foundation Design and Technology is a two year Entry Level and Level 1 course for learners aged 14 to 16, taken in Engineering Design, Fashion and Textiles or Product Design. Literacy runs through both units: the Unit 1 topic tests use objective and short answer questions full of technical vocabulary on safety, materials and processes, and the Unit 2 design project asks learners to analyse an existing product, write a design brief and specification, annotate and present ideas and evaluate their prototype. Numeracy is lighter and practical: setting sizes in the specification, measuring and drawing accurately, planning time across a 40 hour project and, in Engineering Design, knowing volts, amps and ohms. KS3 should build clear technical writing alongside accurate measuring in millimetres.
- Corff dyfarnu
- CBAC
- Lefel
- Entry Level and Level 1
- Addysgu gyntaf
- Medi 2027
- Faint o waith llythrennedd
- Canolig
- Faint o waith rhifedd
- Isel
- Manyleb
- Agor y fanyleb
Sut mae'r cymhwyster hwn yn cael ei asesu
- Unit 1: Design and Technology in the 21st Century: Three topic tests of 20 minutes each (1 hour in total): a Core Knowledge and Understanding test on health and safety (16 marks) and two pathway tests on Materials and Components and on Tools, Techniques and Processes (12 marks each), 40 marks, 30%, set and marked by WJEC, digital or paper format within a four week window
- Unit 2: Design Project: Non-examination assessment, a sustained design and make task of approximately 40 hours based on a contextual challenge set by the centre, 60 marks, 70%, set and marked by the centre and moderated by WJEC
Sgiliau sy'n defnyddio Ongl
-
Drawing ideas in 2D and 3D and to scale
Learners may communicate their ideas with formal and informal 2D and 3D drawing, and present their final design with details that support manufacturing, such as sizes. Formal drawing needs accurate dimensions, angles and scale.
Rhifedd: Siâp a gofod, Dealltwriaeth gysyniadol, Ongl
Paratoi disgyblion
- Blwyddyn 7
- Pupils sketch a box-shaped product in 3D on isometric grid paper and label its length, width and height.
- Blwyddyn 8
- Pupils draw the front and side views of their idea at half size and an isometric view using 30 degree lines measured with a protractor.
- Blwyddyn 9
- Pupils produce a dimensioned working drawing of their final design at a stated scale, showing every size needed to make it.
Dangos geiriad y fanyleb a datganiadau'r Fframwaith Llythrennedd a Rhifedd
Ble mae yn y fanyleb: Unit 2, Section 2.1.3, page 21
“formal and informal 2d and/or 3d drawing”
Cam cynnydd 3
Rwy'n gallu defnyddio iaith fathemategol i ddisgrifio siapiau dau ddimensiwn a thri dimensiwn yn gywir.
Rwy'n gallu cynrychioli cysyniad mewn ffyrdd gwahanol, gan lifo rhwng cynrychioliadau gwahanol gan gynnwys rhai llafar, diriaethol, gweledol, digidol a haniaethol.
Cam cynnydd 4
Rwy'n gallu mesur a lluniadu onglau.
Rwy'n gallu cymhwyso dealltwriaeth o gyfeiriannau a graddfa i ddehongli mapiau a chynlluniau, ac i greu cynlluniau a lluniadau wrth raddfa.
Da gwybod
- Unit 1 questions are short: the topic tests use "multiple choice questions (MCQ), objective test questions (OTQ) and short answer questions" and can be sat on paper or on screen (Section 3.2, page 25).
- No marks for spelling, punctuation and grammar are mentioned; all marks sit under AO1 to AO4 (Section 3.1, page 24), and "The Assessment Pack will include all detailed information relating to assessment." (page 24).
- Writing in Unit 2 is marked through annotation: "Written evidence must be annotated to show how it meets the marking criteria." (Section 3.3, page 26).
- Spoken work such as presentations is evidenced by the teacher: performance evidence "must be documented using observation records" (Section 3.3, page 26).
- Numeracy is not named in the content, and calculations are not listed; Engineering Design learners only need to know "the following measurements within the electronical circuits:" volts, amps and ohms (Unit 1, page 14).
- Appendix A (pages 32 and 33) ticks Listening, Reading, Speaking and Writing for both units, but ticks only "Developing Mathematical Proficiency" for Unit 2 and none of the number, geometry and measurement or statistics strands.
Cysylltiadau â chymwysterau eraill
The specification says the qualification "provides a broad basis for progression onto GCSE Design and Technology" (page 8). The Foundation shares the GCSE's design brief, specification, annotation and evaluation writing and its technical vocabulary, but tests knowledge through short answer topic tests rather than extended written answers. GCSE Design and Technology steps up the numeracy, with measuring to tolerances, estimating material quantities, waste and costs, using collated data to set specification criteria, scale drawing and, in Engineering Design, mechanical and electronic calculations. Accurate measuring and unit work also link with GCSE Mathematics and Numeracy.
Ffynhonnell: WJEC Entry Level/Level 1 Foundation Design and Technology specification, approved by Qualifications Wales, teaching from September 2027, for award from 2029 (© WJEC CBAC Ltd 2026).