Foundation Design and Technology
Mae disgrifiad y cymhwyster yn Saesneg yn unig, gan ei fod wedi ei gymryd o fanyleb Saesneg CBAC.
Foundation Design and Technology is a two year Entry Level and Level 1 course for learners aged 14 to 16, taken in Engineering Design, Fashion and Textiles or Product Design. Literacy runs through both units: the Unit 1 topic tests use objective and short answer questions full of technical vocabulary on safety, materials and processes, and the Unit 2 design project asks learners to analyse an existing product, write a design brief and specification, annotate and present ideas and evaluate their prototype. Numeracy is lighter and practical: setting sizes in the specification, measuring and drawing accurately, planning time across a 40 hour project and, in Engineering Design, knowing volts, amps and ohms. KS3 should build clear technical writing alongside accurate measuring in millimetres.
- Corff dyfarnu
- CBAC
- Lefel
- Entry Level and Level 1
- Addysgu gyntaf
- Medi 2027
- Faint o waith llythrennedd
- Canolig
- Faint o waith rhifedd
- Isel
- Manyleb
- Agor y fanyleb
Sut mae'r cymhwyster hwn yn cael ei asesu
- Unit 1: Design and Technology in the 21st Century: Three topic tests of 20 minutes each (1 hour in total): a Core Knowledge and Understanding test on health and safety (16 marks) and two pathway tests on Materials and Components and on Tools, Techniques and Processes (12 marks each), 40 marks, 30%, set and marked by WJEC, digital or paper format within a four week window
- Unit 2: Design Project: Non-examination assessment, a sustained design and make task of approximately 40 hours based on a contextual challenge set by the centre, 60 marks, 70%, set and marked by the centre and moderated by WJEC
Sgiliau sy'n defnyddio Deall, ymateb a dadansoddi
-
Describing hazards, safety signs and safe working practices
All learners take a health and safety topic test covering PPE, safety signs and hazard symbols, manual handling and electrical safety. They must identify and describe hazards and safe working practices as part of risk assessment, reading signs and symbols and explaining them in words.
Llythrennedd: Deall, ymateb a dadansoddi, Cynllunio a threfnu ar gyfer gwahanol ddibenion, cynulleidfaoedd a chyd-destunau
Paratoi disgyblion
- Blwyddyn 7
- Pupils read the safety signs around the workshop and write what each one means and which colour group it belongs to.
- Blwyddyn 8
- Pupils write a simple risk assessment for the pillar drill, describing two hazards and the safe working practice for each in full sentences.
- Blwyddyn 9
- Pupils read a manufacturer's safety sheet for a hot glue gun or sewing machine and write a short risk assessment that names the hazards, who is at risk and how to work safely.
Dangos geiriad y fanyleb a datganiadau'r Fframwaith Llythrennedd a Rhifedd
Ble mae yn y fanyleb: Unit 1, Section 1.1.1, page 12
“Learners should be able to identify and describe risk assessment procedures”
Cam cynnydd 3
Rwy'n gallu darllen yn fanwl, gan adnabod a nodi nodweddion testunau, e.e. cyflwyniad, dilyniant, darluniau, ffurfioldeb, geirfa allweddol.
Rwy'n gallu defnyddio ac addasu gwahanol strwythurau yn fy ngwaith ysgrifennu, e.e. adroddiad ar ddigwyddiad, ymchwiliad neu arbrawf.
Cam cynnydd 4
Rwy'n gallu darllen yn fanwl, gwneud gwaith dilynol a defnyddio deunyddiau ychwanegol mewn testunau i ymestyn fy nealltwriaeth.
Rwy'n gallu addasu fy arddull ysgrifennu, gan ddewis a defnyddio'r strwythurau gorau ar gyfer gwahanol gyd-destunau a dibenion, e.e. i ddisgrifio, esbonio, darbwyllo, trafod yn llwyddiannus.
-
Analysing existing products and the work of designers
In Unit 2 learners explore and investigate existing products and the work of design professionals, and analyse and evaluate an existing product relevant to their own design work. This means reading product information and reviews and pulling out what matters for their own users.
Llythrennedd: Deall, ymateb a dadansoddi
Paratoi disgyblion
- Blwyddyn 7
- Pupils look at an existing torch and its packaging and write down who it is for, what it does and what it is made from.
- Blwyddyn 8
- Pupils read two product reviews of the same backpack and summarise what users like and dislike about it.
- Blwyddyn 9
- Pupils analyse an existing product related to their project using the maker's website, reviews and their own handling of it, then write which features they will use or improve.
Dangos geiriad y fanyleb a datganiadau'r Fframwaith Llythrennedd a Rhifedd
Ble mae yn y fanyleb: Unit 2, Section 2.1.1, page 20; Unit 2, Section 2.1.3, page 21
“analyse and evaluate an existing product that is relevant to their own design work”
Cam cynnydd 3
Rwy'n gallu defnyddio ffynonellau cyfeirio/digidol i ddewis, crynhoi a chyfuno gwybodaeth, gan gyfeirio atyn nhw fel y bo'n briodol.
Rwy'n gallu coladu a gwneud cysylltiadau, e.e blaenoriaethu, categoreiddio, rhwng gwybodaeth a syniadau o wahanol ffynonellau gan gynnwys testunau digidol a chlyweledol.
Cam cynnydd 4
Rwy'n gallu ymchwilio i amrywiaeth eang o ffynonellau cyfeirio a digidol er mwyn datblygu dealltwriaeth lawn o bwnc neu fater.
Rwy'n gallu crynhoi, cyfuno a dadansoddi gwybodaeth er mwyn magu dealltwriaeth fanwl, e.e. o achosion, canlyniadau, patrymau, gan ddefnyddio gwahanol ffynonellau.
Da gwybod
- Unit 1 questions are short: the topic tests use "multiple choice questions (MCQ), objective test questions (OTQ) and short answer questions" and can be sat on paper or on screen (Section 3.2, page 25).
- No marks for spelling, punctuation and grammar are mentioned; all marks sit under AO1 to AO4 (Section 3.1, page 24), and "The Assessment Pack will include all detailed information relating to assessment." (page 24).
- Writing in Unit 2 is marked through annotation: "Written evidence must be annotated to show how it meets the marking criteria." (Section 3.3, page 26).
- Spoken work such as presentations is evidenced by the teacher: performance evidence "must be documented using observation records" (Section 3.3, page 26).
- Numeracy is not named in the content, and calculations are not listed; Engineering Design learners only need to know "the following measurements within the electronical circuits:" volts, amps and ohms (Unit 1, page 14).
- Appendix A (pages 32 and 33) ticks Listening, Reading, Speaking and Writing for both units, but ticks only "Developing Mathematical Proficiency" for Unit 2 and none of the number, geometry and measurement or statistics strands.
Cysylltiadau â chymwysterau eraill
The specification says the qualification "provides a broad basis for progression onto GCSE Design and Technology" (page 8). The Foundation shares the GCSE's design brief, specification, annotation and evaluation writing and its technical vocabulary, but tests knowledge through short answer topic tests rather than extended written answers. GCSE Design and Technology steps up the numeracy, with measuring to tolerances, estimating material quantities, waste and costs, using collated data to set specification criteria, scale drawing and, in Engineering Design, mechanical and electronic calculations. Accurate measuring and unit work also link with GCSE Mathematics and Numeracy.
Ffynhonnell: WJEC Entry Level/Level 1 Foundation Design and Technology specification, approved by Qualifications Wales, teaching from September 2027, for award from 2029 (© WJEC CBAC Ltd 2026).