LNF Cymru Llythrennedd a rhifedd i Gymru

← Pob cymhwyster

Foundation Engineering

Mae disgrifiad y cymhwyster yn Saesneg yn unig, gan ei fod wedi ei gymryd o fanyleb Saesneg CBAC.

Foundation Engineering is a two-year Entry Level to Level 1 work-related qualification for learners in Years 10 and 11, leading on to VCSE Engineering. Literacy sits mostly in Unit 1, where learners name, outline, describe and explain engineering roles, tools, processes and safety rules through talks, presentations, short reports and matching tasks, and in Unit 2, where they read risk assessments, write a task plan, record results and report faults. Numeracy sits in the Unit 2 workshop: reading dimensions and angles on drawings, marking out, measuring with steel rules, vernier callipers and micrometers, and working to tolerances that tighten from plus or minus 2 mm at Entry 1 to plus or minus 0.8 mm at Level 1. There are no formulae or written tests.

Corff dyfarnu
CBAC
Lefel
Entry Level and Level 1
Addysgu gyntaf
Medi 2027
Faint o waith llythrennedd
Canolig
Faint o waith rhifedd
Canolig
Manyleb
Agor y fanyleb
Y cam nesaf i fyny
VCSE Engineering, Level 1 and Level 2
Sut mae'r cymhwyster hwn yn cael ei asesu
  • Unit 1: Introduction to Engineering: Centre marked non-examination assessment, portfolio of evidence, maximum assessment time 9 hours (typically 7 to 9 hours), 36 guided learning hours, 48 points of the 112 qualification points, teacher-set tasks assessed in centre and moderated by WJEC, first available summer 2028
  • Unit 2: Producing a Product: Centre marked non-examination assessment, portfolio of evidence, maximum assessment time 21 hours (typically 19 to 21 hours), 84 guided learning hours, 64 points of the 112 qualification points, teacher-set practical workshop tasks assessed in centre and moderated by WJEC, first available summer 2029

Sgiliau sy'n defnyddio Cyfathrebu â symbolau

  1. Working to tolerances and recording the results

    Asesu: Mewn gwaith cwrs (asesiad di-arholiad)

    Learners cut and shape materials within set tolerances, then check and record the results. The criteria tighten from plus or minus 2 mm at Entry 1 to plus or minus 0.8 mm at Level 1 for hand fitting, and from plus or minus 7 mm to 4 mm for sheet metal. Entry 3 learners compare measurements with tolerances and record them with units, and Level 1 learners present measurement records in tables or inspection sheets.

    Rhifedd: Cyfrifiad, Rhesymu rhesymegol, Cyfathrebu â symbolau

    Paratoi disgyblion

    Blwyddyn 7
    Pupils cut a strip to 100 mm and check whether it is within 2 mm, writing down the smallest and largest sizes that would pass.
    Blwyddyn 8
    Pupils work out the upper and lower limits for sizes such as 50 mm plus or minus 1.5 mm and decide which of a set of measured parts pass.
    Blwyddyn 9
    Pupils file a part to 40 mm plus or minus 0.8 mm, measure it with a vernier calliper and record the drawing size, limits, measured size in mm and a pass or fail on an inspection sheet.
    Dangos geiriad y fanyleb a datganiadau'r Fframwaith Llythrennedd a Rhifedd

    Ble mae yn y fanyleb: Unit 2, Sections 2.3.4, 2.4.2 and 2.4.3, page 32; Unit 2, assessment criteria, page 36; Unit 2, LO2.4 example tasks, page 42; Unit 2, portfolio evidence, page 44

    “the learner compares measured dimensions to given tolerances”
    Cam cynnydd 3
    • Rwy'n gallu adio a thynnu rhifau gan ddefnyddio rhifau cyfan a degolion.

    • Rwy'n gallu dilysu canlyniadau a datrysiadau.

    • Rwy'n gallu defnyddio nodiant, symbolau ac unedau mesur priodol.

    Cam cynnydd 4
    • Rwy'n gallu defnyddio dulliau ysgrifenedig effeithlon i adio a thynnu rhifau a degolion o unrhyw faint, gan gynnwys cymysgedd o rifau mawr a bach â niferoedd gwahanol o leoedd degol.

    • Rwy'n gallu dilysu a phrofi canlyniadau a datrysiadau.

    • Rwy'n gallu defnyddio nodiant, symbolau ac unedau mesur priodol, gan gynnwys mesurau cyfansawdd.

Da gwybod

Cysylltiadau â chymwysterau eraill

Foundation Engineering is the step below VCSE Engineering, which the specification names as a progression route. Both ask learners to read drawings, measure with vernier callipers and micrometers, work to tolerances, write a plan and risk assessment, record results and suggest improvements. VCSE Engineering steps these up with closer tolerances judged against full engineering drawings, unit conversions, area, volume and waste, spindle speed and Ohm's law calculations in a one hour written test, and reading a case study on an engineering project in Wales. The measuring and recording work also links with GCSE Mathematics and Numeracy and GCSE Design and Technology, and the talks and reports build on GCSE English Language and Literature skills.

Ffynhonnell: WJEC Entry Level/Level 1 Foundation Engineering specification, approved by Qualifications Wales, teaching from September 2027, for award from 2029 (© WJEC CBAC Ltd 2026).