Foundation Engineering
Mae disgrifiad y cymhwyster yn Saesneg yn unig, gan ei fod wedi ei gymryd o fanyleb Saesneg CBAC.
Foundation Engineering is a two-year Entry Level to Level 1 work-related qualification for learners in Years 10 and 11, leading on to VCSE Engineering. Literacy sits mostly in Unit 1, where learners name, outline, describe and explain engineering roles, tools, processes and safety rules through talks, presentations, short reports and matching tasks, and in Unit 2, where they read risk assessments, write a task plan, record results and report faults. Numeracy sits in the Unit 2 workshop: reading dimensions and angles on drawings, marking out, measuring with steel rules, vernier callipers and micrometers, and working to tolerances that tighten from plus or minus 2 mm at Entry 1 to plus or minus 0.8 mm at Level 1. There are no formulae or written tests.
- Corff dyfarnu
- CBAC
- Lefel
- Entry Level and Level 1
- Addysgu gyntaf
- Medi 2027
- Faint o waith llythrennedd
- Canolig
- Faint o waith rhifedd
- Canolig
- Manyleb
- Agor y fanyleb
- Y cam nesaf i fyny
- VCSE Engineering, Level 1 and Level 2
Sut mae'r cymhwyster hwn yn cael ei asesu
- Unit 1: Introduction to Engineering: Centre marked non-examination assessment, portfolio of evidence, maximum assessment time 9 hours (typically 7 to 9 hours), 36 guided learning hours, 48 points of the 112 qualification points, teacher-set tasks assessed in centre and moderated by WJEC, first available summer 2028
- Unit 2: Producing a Product: Centre marked non-examination assessment, portfolio of evidence, maximum assessment time 21 hours (typically 19 to 21 hours), 84 guided learning hours, 64 points of the 112 qualification points, teacher-set practical workshop tasks assessed in centre and moderated by WJEC, first available summer 2029
Sgiliau sy'n defnyddio Cymhwysedd strategol
-
Marking out accurately with rules, squares and protractors
Learners mark out bar stock, flat or sheet materials and round sections, by direct marking with instruments and with templates. They use dividers or trammels, protractors, punches, scribers, squares and steel rules or tape measures.
Rhifedd: Mesur, Ongl, Cymhwysedd strategol
Paratoi disgyblion
- Blwyddyn 7
- Pupils mark out a 60 mm by 40 mm rectangle on card with a steel rule and try square and check each side.
- Blwyddyn 8
- Pupils mark out a plate with a 30 degree corner using a protractor and a 20 mm radius curve using dividers.
- Blwyddyn 9
- Pupils mark out a metal plate from a drawing with hole centres, a chamfer and a radius, punching the hole centres and checking every size before cutting.
Dangos geiriad y fanyleb a datganiadau'r Fframwaith Llythrennedd a Rhifedd
Ble mae yn y fanyleb: Unit 2, Section 2.3.2, page 31; Unit 2, LO2.3 example tasks, page 41
“Use a range of marking out equipment including:”
Cam cynnydd 3
Rwy'n gallu darllen a dehongli graddfeydd neu raniadau ar amrywiaeth o offerynnau mesur.
Rwy'n gallu defnyddio ongl fel mesur cylchdro.
Cam cynnydd 4
Rwy'n gallu mesur a lluniadu onglau.
Rwy'n gallu nodi, mesur neu gasglu'r wybodaeth sy'n ofynnol er mwyn cwblhau'r dasg.
-
Using technical data such as thread sizes and cutting speeds
Learners interpret technical information including cutting speeds, thread sizes and tolerances from drawings and charts, and use it to complete making tasks. At Level 1 they use technical data such as thread specifications and tolerances to carry out a task or make a decision.
Rhifedd: Dehongli data, Cymhwysedd strategol
Paratoi disgyblion
- Blwyddyn 7
- Pupils read a drill size chart to find which drill makes a 5 mm hole and which makes a 6.5 mm hole.
- Blwyddyn 8
- Pupils use a tapping drill table to find the drill size needed before cutting an M6 thread and an M8 thread.
- Blwyddyn 9
- Pupils use a cutting speed chart to choose drill speeds for mild steel and aluminium at two hole sizes, and explain the pattern they see in the chart.
Dangos geiriad y fanyleb a datganiadau'r Fframwaith Llythrennedd a Rhifedd
Ble mae yn y fanyleb: Unit 2, Sections 2.1.2 and 2.1.3, page 30; Unit 2, LO2.1 example tasks, page 39
“the learner uses technical data, such as thread specifications and tolerances”
Cam cynnydd 3
Rwy'n gallu echdynnu a dehongli gwybodaeth o amrywiaeth gynyddol o ddiagramau, amserlenni a graffiau (gan gynnwys siartiau cylch).
Rwy'n gallu nodi, mesur neu gasglu'r wybodaeth sy'n ofynnol er mwyn cwblhau'r dasg.
Cam cynnydd 4
Rwy'n gallu dehongli gwybodaeth fathemategol; gan ddod i gasgliadau o graffiau, diagramau a data, gan gynnwys trafod cyfyngiadau data.
Rwy'n gallu nodi, mesur neu gasglu'r wybodaeth sy'n ofynnol er mwyn cwblhau'r dasg.
Da gwybod
- There are no written tests. Both units are a "Portfolio of evidence" that is "Assessed in centre and moderated by WJEC" (Summary of assessment, page 5), so literacy and numeracy are shown through practical work, writing and talk.
- Spoken work counts: evidence types include "teacher/assessor questioning" with "responses to structured questions, either written or oral, to confirm understanding" (Section 3.3, page 47), and presentations are recorded on "observation records" (Section 3.6, page 48).
- Support varies by level: Entry 1 learners may need "use of symbols, or assistive technology" and Entry 2 learners may use "scaffolded templates" (Section 3.4, page 48).
- No marks for spelling, punctuation and grammar are mentioned; "judgements are made solely against the assessment criteria" (Section 3.6, page 48).
- The numeracy is measurement rather than calculation. Learners work "within general set tolerances" (Section 2.3.4, page 32), from plus or minus 2 mm to 0.8 mm for hand fitting (page 36), and the specification has no formulae, area, volume or calculator work, unlike VCSE Engineering.
- Appendix A (pages 55 and 56) maps listening, reading, speaking and writing to every Unit 1 section, speaking and writing to Unit 2 planning (2.2.1) and recording outcomes (2.4.3), and all four numeracy strands, including statistics, to 1.3.1, 1.3.2 and most of Unit 2.
Cysylltiadau â chymwysterau eraill
Foundation Engineering is the step below VCSE Engineering, which the specification names as a progression route. Both ask learners to read drawings, measure with vernier callipers and micrometers, work to tolerances, write a plan and risk assessment, record results and suggest improvements. VCSE Engineering steps these up with closer tolerances judged against full engineering drawings, unit conversions, area, volume and waste, spindle speed and Ohm's law calculations in a one hour written test, and reading a case study on an engineering project in Wales. The measuring and recording work also links with GCSE Mathematics and Numeracy and GCSE Design and Technology, and the talks and reports build on GCSE English Language and Literature skills.
Ffynhonnell: WJEC Entry Level/Level 1 Foundation Engineering specification, approved by Qualifications Wales, teaching from September 2027, for award from 2029 (© WJEC CBAC Ltd 2026).