VCSE Engineering
Mae disgrifiad y cymhwyster yn Saesneg yn unig, gan ei fod wedi ei gymryd o fanyleb Saesneg CBAC.
VCSE Engineering asks learners to read engineering drawings and technical sources closely, use precise technical vocabulary, write an operations plan and risk assessment, report faults and evaluate the quality of their own work, while the Unit 1 tasks ask them to read a case study and weigh the benefits and challenges of an engineering project in Wales. Numeracy runs through every unit: measuring to tolerances with callipers and micrometers, finding missing dimensions and angles on drawings, converting units, and calculating area, volume, waste, feeds and speeds and Ohm's law, much of it tested in the one hour Unit 3 written test. The single biggest thing KS3 should build is accurate measuring in millimetres against a stated tolerance, together with the confidence to use a formula such as spindle speed or Ohm's law with the right units.
- Corff dyfarnu
- CBAC
- Lefel
- Level 1 and Level 2
- Addysgu gyntaf
- Medi 2027
- Faint o waith llythrennedd
- Canolig
- Faint o waith rhifedd
- Uchel
- Manyleb
- Agor y fanyleb
- Y cam cyn hyn
- Foundation Engineering, Entry Level and Level 1
Sut mae'r cymhwyster hwn yn cael ei asesu
- Unit 1: Introduction to the Engineering Sector: Non-examination assessment 8 hours, 20%, 40 marks, set and marked by WJEC, available via Portal
- Unit 2: Applying Engineering Processes: Non-examination assessment 26 hours, 60%, 145 marks, set by WJEC, marked by the centre and moderated by WJEC
- Unit 3: Engineering Principles: Written test 1 hour, 20%, 60 marks, set and marked by WJEC, paper format only
Sgiliau sy'n defnyddio Y system rif
-
Measuring accurately and working to tolerances
Learners measure and mark out with steel rules, vernier, dial and digital callipers and micrometers, identify the tolerances a component needs, and evaluate the accuracy of their dimensions against the drawing. Unit 3 examines the purpose of gauging and measuring tools and why each suits an operation.
Rhifedd: Mesur, Y system rif, Cymhwysedd strategol, Cyfathrebu â symbolau
Paratoi disgyblion
- Blwyddyn 7
- Pupils mark out a 60 mm by 40 mm plate with a steel rule and engineers square, then check that every side is within 1 mm of the drawing.
- Blwyddyn 8
- Pupils measure the same rod with vernier callipers and digital callipers, record each reading to two decimal places and explain any difference.
- Blwyddyn 9
- Pupils measure five features of a finished part with digital callipers or a micrometer, work out the upper and lower limits from a tolerance such as 25 mm plus or minus 0.1 mm, and decide which features pass.
Dangos geiriad y fanyleb a datganiadau'r Fframwaith Llythrennedd a Rhifedd
Ble mae yn y fanyleb: Unit 2, Sections 2.2.1 and 2.2.2, page 20; Unit 2, Section 2.4.2, page 26; Unit 3, Section 3.1.1, page 29
“Learners understand the quality of the engineering outcomes against tolerances stated in the engineering drawings”
Cam cynnydd 3
Rwy'n gallu darllen a dehongli graddfeydd neu raniadau ar amrywiaeth o offerynnau mesur.
Rwy'n gallu cofnodi mesuriadau mewn ffyrdd gwahanol, e.e. 1.3kg = 1kg 300g, 4.2cm = 4cm 2mm.
Rwy'n gallu trosi unedau metrig o hyd i unedau llai, e.e. cm i mm, m i cm, km i m.
Cam cynnydd 4
Rwy'n gallu darllen a dehongli graddfeydd ar amrywiaeth o offerynnau mesur.
Rwy'n gallu defnyddio'r unedau mesur cyffredin, trosi rhwng unedau cysylltiedig y system fetrig a chwblhau cyfrifiadau.
Rwy'n gallu dewis y radd briodol o gywirdeb i gyflwyno atebion.
Cam cynnydd 5
Rwy'n gallu adnabod a diffinio cyfyngiadau ar gywirdeb mesuriadau, e.e. ffiniau uchaf ac isaf.
Rwy'n gallu nodi, mesur neu gasglu'r wybodaeth sy'n ofynnol er mwyn cwblhau'r dasg.
Rwy'n gallu defnyddio nodiant, symbolau ac unedau mesur priodol, gan gynnwys mesurau cyfansawdd.
Da gwybod
- Numeracy is named in the content itself: learners use "applying numeracy skills to calculate or determine missing or incorrect dimensions where required" (Unit 2, Section 2.1.1, page 19), and Unit 3 lists "GCSE Mathematics and Numeracy" as a linked qualification (page 28).
- No marks for spelling, punctuation and grammar are mentioned. All marks sit under AO1 to AO4 (Section 3.1, page 37), and "The Assessment Pack will include all detailed information relating to assessment." (page 37).
- Calculator use is not stated, although Unit 3 includes feeds and speeds and Ohm's law calculations and "Unit 3 is a written test, available in paper format only." (page 5). Check the Assessment Pack.
- NEA writing may be handwritten: evidence "must be submitted digitally, either as scanned handwritten responses or completed digitally." (page 38).
- Spoken and practical work is evidenced by the teacher: "performance evidence (for example, presentations) must be documented using observation records" (Section 3.3, page 40).
- Appendix A (pages 45 to 47) maps literacy to all three units but the numeracy statistics strand to Unit 1 only, and it lists section "3.4.5" (page 47), which does not exist in the content.
Cysylltiadau â chymwysterau eraill
Measuring to tolerances, unit conversions, area and volume and Ohm's law overlap with Mathematics and Numeracy, The Sciences and GCSE Design and Technology. Reading drawings, risk assessments and sector case studies in Wales are shared with VCSE Built Environment.
Ffynhonnell: WJEC Level 1/Level 2 VCSE Engineering specification, approved by Qualifications Wales, teaching from September 2027, for award from 2029 (© WJEC CBAC Ltd 2026).