VCSE Engineering
VCSE Engineering asks learners to read engineering drawings and technical sources closely, use precise technical vocabulary, write an operations plan and risk assessment, report faults and evaluate the quality of their own work, while the Unit 1 tasks ask them to read a case study and weigh the benefits and challenges of an engineering project in Wales. Numeracy runs through every unit: measuring to tolerances with callipers and micrometers, finding missing dimensions and angles on drawings, converting units, and calculating area, volume, waste, feeds and speeds and Ohm's law, much of it tested in the one hour Unit 3 written test. The single biggest thing KS3 should build is accurate measuring in millimetres against a stated tolerance, together with the confidence to use a formula such as spindle speed or Ohm's law with the right units.
- Awarding body
- WJEC
- Level
- Level 1 and Level 2
- First taught
- September 2027
- Amount of literacy work
- Medium
- Amount of numeracy work
- High
- Specification
- Open the specification
- Step before
- Foundation Engineering, Entry Level and Level 1
How this qualification is assessed
- Unit 1: Introduction to the Engineering Sector: Non-examination assessment 8 hours, 20%, 40 marks, set and marked by WJEC, available via Portal
- Unit 2: Applying Engineering Processes: Non-examination assessment 26 hours, 60%, 145 marks, set by WJEC, marked by the centre and moderated by WJEC
- Unit 3: Engineering Principles: Written test 1 hour, 20%, 60 marks, set and marked by WJEC, paper format only
Skills that use The number system
-
Measuring accurately and working to tolerances
Learners measure and mark out with steel rules, vernier, dial and digital callipers and micrometers, identify the tolerances a component needs, and evaluate the accuracy of their dimensions against the drawing. Unit 3 examines the purpose of gauging and measuring tools and why each suits an operation.
Numeracy: Measurement, The number system, Strategic competence, Communicating with symbols
Getting pupils ready
- Year 7
- Pupils mark out a 60 mm by 40 mm plate with a steel rule and engineers square, then check that every side is within 1 mm of the drawing.
- Year 8
- Pupils measure the same rod with vernier callipers and digital callipers, record each reading to two decimal places and explain any difference.
- Year 9
- Pupils measure five features of a finished part with digital callipers or a micrometer, work out the upper and lower limits from a tolerance such as 25 mm plus or minus 0.1 mm, and decide which features pass.
Show the specification wording and the LNF statements
Where it is in the specification: Unit 2, Sections 2.2.1 and 2.2.2, page 20; Unit 2, Section 2.4.2, page 26; Unit 3, Section 3.1.1, page 29
“Learners understand the quality of the engineering outcomes against tolerances stated in the engineering drawings”
Progression step 3
I can read and interpret scales or divisions on a range of measuring instruments.
I can record measurements in different ways, e.g. 1.3kg = 1kg 300g, 4.2cm = 4cm 2mm.
I can convert metric units of length to smaller units, e.g. cm to mm, m to cm, km to m.
Progression step 4
I can read and interpret scales on a range of measuring instruments.
I can use the common units of measure, convert between related units of the metric system and carry out calculations.
I can choose the appropriate degree of accuracy to present answers.
Progression step 5
I can recognise and define limitations on accuracy of measurements, e.g. upper and lower bounds.
I can identify, measure or obtain required information to complete the task.
I can use appropriate notation, symbols and units of measurement, including compound measures.
Good to know
- Numeracy is named in the content itself: learners use "applying numeracy skills to calculate or determine missing or incorrect dimensions where required" (Unit 2, Section 2.1.1, page 19), and Unit 3 lists "GCSE Mathematics and Numeracy" as a linked qualification (page 28).
- No marks for spelling, punctuation and grammar are mentioned. All marks sit under AO1 to AO4 (Section 3.1, page 37), and "The Assessment Pack will include all detailed information relating to assessment." (page 37).
- Calculator use is not stated, although Unit 3 includes feeds and speeds and Ohm's law calculations and "Unit 3 is a written test, available in paper format only." (page 5). Check the Assessment Pack.
- NEA writing may be handwritten: evidence "must be submitted digitally, either as scanned handwritten responses or completed digitally." (page 38).
- Spoken and practical work is evidenced by the teacher: "performance evidence (for example, presentations) must be documented using observation records" (Section 3.3, page 40).
- Appendix A (pages 45 to 47) maps literacy to all three units but the numeracy statistics strand to Unit 1 only, and it lists section "3.4.5" (page 47), which does not exist in the content.
Links with other qualifications
Measuring to tolerances, unit conversions, area and volume and Ohm's law overlap with Mathematics and Numeracy, The Sciences and GCSE Design and Technology. Reading drawings, risk assessments and sector case studies in Wales are shared with VCSE Built Environment.
Source: WJEC Level 1/Level 2 VCSE Engineering specification, approved by Qualifications Wales, teaching from September 2027, for award from 2029 (© WJEC CBAC Ltd 2026).