LNF Cymru Literacy and numeracy for Wales

← All qualifications

VCSE Engineering

VCSE Engineering asks learners to read engineering drawings and technical sources closely, use precise technical vocabulary, write an operations plan and risk assessment, report faults and evaluate the quality of their own work, while the Unit 1 tasks ask them to read a case study and weigh the benefits and challenges of an engineering project in Wales. Numeracy runs through every unit: measuring to tolerances with callipers and micrometers, finding missing dimensions and angles on drawings, converting units, and calculating area, volume, waste, feeds and speeds and Ohm's law, much of it tested in the one hour Unit 3 written test. The single biggest thing KS3 should build is accurate measuring in millimetres against a stated tolerance, together with the confidence to use a formula such as spindle speed or Ohm's law with the right units.

Awarding body
WJEC
Level
Level 1 and Level 2
First taught
September 2027
Amount of literacy work
Medium
Amount of numeracy work
High
Specification
Open the specification
Step before
Foundation Engineering, Entry Level and Level 1
How this qualification is assessed
  • Unit 1: Introduction to the Engineering Sector: Non-examination assessment 8 hours, 20%, 40 marks, set and marked by WJEC, available via Portal
  • Unit 2: Applying Engineering Processes: Non-examination assessment 26 hours, 60%, 145 marks, set by WJEC, marked by the centre and moderated by WJEC
  • Unit 3: Engineering Principles: Written test 1 hour, 20%, 60 marks, set and marked by WJEC, paper format only

Skills that use Shape and space

  1. Finding missing dimensions and angles on engineering drawings

    Assessed: In the exam and in coursework (NEA)

    Learners apply numeracy to calculate missing or incorrect dimensions on drawings and calculate angles and sizes in Unit 2. In Unit 3 they construct third angle projections with a 45 degree line and isometric drawings with 30 degree lines, and dimension drawings to BS 8888.

    Numeracy: Angle, Calculation, Shape and space, Strategic competence, Logical reasoning

    Getting pupils ready

    Year 7
    Pupils work out the missing lengths on a dimensioned drawing of an L-shaped plate by adding and subtracting the given sizes.
    Year 8
    Pupils draw a simple block in isometric using 30 degree lines measured with a protractor, then draw its front, side and plan views to scale.
    Year 9
    Pupils check a drawing with deliberate mistakes, calculate the missing or wrong dimensions and the angle of a 45 degree chamfer, and correct them in a different colour.
    Show the specification wording and the LNF statements

    Where it is in the specification: Unit 2, Sections 2.1.1 and 2.1.3, page 19; Unit 3, Sections 3.2.2 to 3.2.4, pages 32 and 33

    “applying numeracy skills to calculate or determine missing or incorrect dimensions where required”
    Progression step 3
    • I can use angle as a measure of rotation.

    • I can add and subtract numbers using whole numbers and decimals.

    • I can use mathematical language to accurately describe two-dimensional and three-dimensional shapes.

    Progression step 4
    • I can measure and draw angles.

    • I can apply understanding of bearings and scale to interpret maps and plans, and to create plans and drawings to scale.

    • I can use efficient written methods to add and subtract numbers and decimals of any size, including a mixture of large and small numbers with differing numbers of decimal places.

    Progression step 5
    • I can measure and draw angles.

    • I can identify, measure or obtain required information to complete the task.

    • I can verify and prove results and solutions.

  2. Calculating area, volume and material waste

    Assessed: In the exam

    Learners calculate the surface area and volume of quadrilaterals, triangles, circles and compound shapes in engineering scenarios, including quantities of material, waste and maximising material use through tessellation. This is examined in the Unit 3 written test.

    Numeracy: Shape and space, Strategic competence, Conceptual understanding

    Getting pupils ready

    Year 7
    Pupils use the area of rectangles to work out how many 50 mm by 30 mm keyring blanks can be cut from a 300 mm by 200 mm sheet of acrylic.
    Year 8
    Pupils tessellate their design shapes on a sheet to get the most parts from it and calculate the percentage of the sheet that is wasted.
    Year 9
    Pupils calculate the volume of a turned aluminium part made from a cylinder with a hole through it, and the volume of metal removed as waste from the starting bar.
    Show the specification wording and the LNF statements

    Where it is in the specification: Unit 3, Section 3.4.2, page 35

    “calculation of waste materials”
    Progression step 3
    • I can measure and calculate perimeter.

    • I can find areas by counting squares, progressing to calculating the area of squares and rectangles using formulae.

    • I can find volumes by counting and other practical methods.

    Progression step 4
    • I can find circumferences of circles using my understanding of π (Pi).

    • I can calculate the areas of two-dimensional simple and compound shapes, including circles.

    • I can apply the formulae for the volume of simple prisms.

    Progression step 5
    • I can recognise, model and apply the underlying mathematical structures and ideas within problems, in order to formulate and solve them.

    • I can select, trial and evaluate a variety of possible approaches and break complex problems into a series of tasks.

    • I can interpret answers within the context of the problem and consider whether answers, including calculator, analogue and digital displays, are sensible.

Good to know

Links with other qualifications

Measuring to tolerances, unit conversions, area and volume and Ohm's law overlap with Mathematics and Numeracy, The Sciences and GCSE Design and Technology. Reading drawings, risk assessments and sector case studies in Wales are shared with VCSE Built Environment.

Source: WJEC Level 1/Level 2 VCSE Engineering specification, approved by Qualifications Wales, teaching from September 2027, for award from 2029 (© WJEC CBAC Ltd 2026).