LNF Cymru Literacy and numeracy for Wales

← All qualifications

VCSE Engineering

VCSE Engineering asks learners to read engineering drawings and technical sources closely, use precise technical vocabulary, write an operations plan and risk assessment, report faults and evaluate the quality of their own work, while the Unit 1 tasks ask them to read a case study and weigh the benefits and challenges of an engineering project in Wales. Numeracy runs through every unit: measuring to tolerances with callipers and micrometers, finding missing dimensions and angles on drawings, converting units, and calculating area, volume, waste, feeds and speeds and Ohm's law, much of it tested in the one hour Unit 3 written test. The single biggest thing KS3 should build is accurate measuring in millimetres against a stated tolerance, together with the confidence to use a formula such as spindle speed or Ohm's law with the right units.

Awarding body
WJEC
Level
Level 1 and Level 2
First taught
September 2027
Amount of literacy work
Medium
Amount of numeracy work
High
Specification
Open the specification
Step before
Foundation Engineering, Entry Level and Level 1
How this qualification is assessed
  • Unit 1: Introduction to the Engineering Sector: Non-examination assessment 8 hours, 20%, 40 marks, set and marked by WJEC, available via Portal
  • Unit 2: Applying Engineering Processes: Non-examination assessment 26 hours, 60%, 145 marks, set by WJEC, marked by the centre and moderated by WJEC
  • Unit 3: Engineering Principles: Written test 1 hour, 20%, 60 marks, set and marked by WJEC, paper format only

Skills that use Planning and organising for different purposes, audiences and context

  1. Writing an operations plan and risk assessment

    Assessed: In coursework (non-examination assessment, NEA)

    Learners write a plan of their engineering operations that details technical information, time frames, priorities and the sequence of processes, and a risk assessment that sets out risks, control measures and revised risk levels. Both are clear procedural writing that the learner then has to follow safely in Unit 2.

    Literacy: Planning and organising for different purposes, audiences and context

    Getting pupils ready

    Year 7
    Pupils write numbered instructions for safely marking out and cutting a piece of acrylic, using command verbs and sequence words.
    Year 8
    Pupils write a risk assessment table for the pillar drill, describing each hazard, risk and control measure in a clear full sentence.
    Year 9
    Pupils write a full operations plan for a small project with technical detail, timings and quality checks, then redraft it after a partner tries to follow it and marks anything unclear.
    Show the specification wording and the LNF statements

    Where it is in the specification: Unit 2, Sections 2.2.1 and 2.2.3, pages 20 and 21

    “plan the engineering operations, including:”
    Progression step 3
    • I can use and adapt different structures within my writing, e.g. reporting an event, investigation or experiment.

    • I can explore different ways to plan, draft and present my work appropriately.

    Progression step 4
    • I can select and use appropriate strategies to plan and develop my writing for different purposes and audiences.

    • I can adapt my writing style, choosing and using the best structures for different contexts and purposes, e.g. to successfully describe, explain, persuade, discuss.

    Progression step 5
    • I can select and use appropriate strategies to plan and develop my writing for a challenging range of different purposes and audiences.

    • I can organise writing in an appropriate form, ensuring content is detailed within and between paragraphs or sections, developing and sustaining ideas coherently.

  2. Evaluating quality and suggesting improvements in writing

    Assessed: In coursework (non-examination assessment, NEA)

    Learners evaluate the quality of their components against drawing tolerances, judge how well their chosen processes worked and whether they finished in the planned time, and suggest realistic improvements. This evaluation sits in the Unit 2 tasks, where AO3, interpreting and evaluating, carries 10% of the qualification.

    Literacy: Planning and organising for different purposes, audiences and context, Connectives and syntax

    Getting pupils ready

    Year 7
    Pupils write three sentences about their finished project: one thing that went well, one that did not, and what they would do differently next time.
    Year 8
    Pupils write a paragraph evaluating their part using measurements as evidence and connectives such as because, however and as a result.
    Year 9
    Pupils write a structured evaluation with sections on accuracy, finish, process choice and time, ending with two realistic improvements that each name a process, tool or material.
    Show the specification wording and the LNF statements

    Where it is in the specification: Unit 2, Sections 2.4.2 and 2.4.3, page 26; Section 3.1, page 37

    “how to suggest realistic improvements that would benefit”
    Progression step 3
    • I can use and adapt different structures within my writing, e.g. reporting an event, investigation or experiment.

    • I can use an increasing range of connectives to organise my ideas in sentences, paragraphs and whole texts.

    Progression step 4
    • I can use summary, discussion of issues, detailed explanations and logic when covering a topic.

    • I can use a range of connectives specifically when organising my ideas in whole texts for different purposes.

    Progression step 5
    • I can write extended pieces which include detailed evidence and information for different purposes and audiences within and across different disciplines.

    • I can convey objectivity and impartiality on complex topics, using a range of linguistic devices.

  3. Reading a case study and weighing the benefits and challenges of an engineering project

    Assessed: In coursework (non-examination assessment, NEA)

    Unit 1 tasks are based on a sector and a case study chosen by WJEC, and learners must understand the potential benefits and challenges of an engineering initiative, project or operation in Wales. They read and research, then write about factors such as economic value, environmental impact, budget and stakeholder conflict.

    Literacy: Understanding, response and analysis, Planning and organising for different purposes, audiences and context

    Getting pupils ready

    Year 7
    Pupils read a short news article about a local engineering project, such as a new bridge or wind farm, and list two benefits and two challenges in their own words.
    Year 8
    Pupils read two short texts about a proposed factory in their area, one from the company and one from local residents, and write a paragraph on benefits and a paragraph on challenges.
    Year 9
    Pupils work through a short case study pack on an engineering project in Wales and write a balanced answer judging whether the benefits outweigh the challenges, quoting evidence from the pack.
    Show the specification wording and the LNF statements

    Where it is in the specification: Unit 1, Section 1.1.3, page 14; Section 3.2, page 37

    “potential challenges of an initiative/project/operation”
    Progression step 3
    • I can show understanding of and use the main ideas and significant details in different texts on the same topic.

    • I can write an effective introduction that establishes context and purpose, a suitable balance between facts and viewpoints, and a precise conclusion.

    Progression step 4
    • I can summarise, synthesise and analyse information to gain in-depth understanding, e.g. of causes, consequences, patterns, using different sources.

    • I can use summary, discussion of issues, detailed explanations and logic when covering a topic.

    Progression step 5
    • I can synthesise and analyse information to gain a broad and balanced understanding from sources which may have conflicting views.

    • I can convey objectivity and impartiality on complex topics, using a range of linguistic devices.

Good to know

Links with other qualifications

Measuring to tolerances, unit conversions, area and volume and Ohm's law overlap with Mathematics and Numeracy, The Sciences and GCSE Design and Technology. Reading drawings, risk assessments and sector case studies in Wales are shared with VCSE Built Environment.

Source: WJEC Level 1/Level 2 VCSE Engineering specification, approved by Qualifications Wales, teaching from September 2027, for award from 2029 (© WJEC CBAC Ltd 2026).